Hakko soldering stations are very good.
Unfortunately, the genuine 230v versions are much more expensive than the 110v models. Don't ask me why, it's probably a Hakko policy, but they can get up to 200$ (in euro or local currencies) when the 110v are about 80-85$ in US.
I say "genuine" versions because there are clones of Hakko FX-888 on eBay and some stores that look almost identical to the original and they're about the same price as the 110v versions, but the insides are totally different, low quality stuff.
I would actually recommend getting a 110v soldering station along with a 220-240v to 110v converter, you will end up cheaper than buying a 230v version of the soldering station.
Question 1. if I were to buy the HAKKO digital Station what is the ideal temp setting? for quite delicate rail soldering(repair)? and for delicate layout/DCC wiring e.t.c.?
There is no ideal temperatures. It depends on the thickness of the wires or leads or part you solder, the tip (size and shape) you use, the base surface on which you want to solder that part.
Basically, you want to solder together two materials, made of copper or other metals... both these metals suck heat from the soldering iron's tip lowering its temperature. The soldering iron will push more power into the tip to counteract this cooling effect.
You know that leaded solder melts at about 180c (60-40 at 180c , 63-37 at 183c) and unleaded solder melts at around 215-217c degrees. You have to use a tip that's big enough so that heat from the tip will flow into the surface and bring it to temperature fast yet you don't want a super high temperature because hot temperature slowly damages the soldering iron's tip oxidizing it. So for example, if there's a very thin strand of wire that I want to solder to a LED lead, I may use 200-220c on the soldering iron and a regular iron tip, but if I want to solder a thicker wire or solder the legs of a heatsink on a PCB, I may switch to a larger iron tip and up the temperature to about 280-320c so that the iron will be able to maintain the temperature.
Question 2. Related to (1) Iron Tips should I use the smallest finest tips when working with DCC & other Layout wiring?please advice on basic number and type of tips I should have(their will be no construction what so ever just wiring repair)as far as I see it.
The default Hakko soldering tip would probably be good enough for such job. Practice is the key though.
Question 3. I keep seeing reference to Tinning? the tips,and I see there are tinning compounds?
The iron tips are tinned from the factory. Tin is basically a large part of the solder wire. leaded solder is 60-40 or 63-37 Tin - Lead (other varieties exist) while unleaded solder is mostly Tin, usually about 97% or more.
The tip is made out of copper and other metals that transfer heat fast but that also means it oxidizes quickly in the presence of air. So it's always a good idea to keep the tip under a thin layer of tin so that air doesn't get to the tip to continue oxidizing it.
So when you start soldering, it's a good idea to clean the tip then apply a bit of solder on the tip so it won't be attacked by air.
Just the same, after soldering, it's a good idea to simply put a bit of solder on the tip and leave it there until the next solder job
Question 4. I currently have some of DCC Concepts SAPHIRE Solder wire & Flux
Are there better options,I should also consider? this is purely out of interest, I can not see a problem withe saphire wire.I will use LEAD wire ?is it still 60/40 grade I should use or a different grade?
I don't know about that solder and flux. It may be good for what you're doing but it may be very bad for electronics, it depends on the flux - some fluxes are acids that corrode the copper and are not suitable for electronics (soldering wires, ICs etc) but are good for pipes and brass but not copper. Unfortunately that site doesn't say the chemical composition of their solder wires and flux. All I can tell from the "Soldering advice" on their page is that their solder may be some kind of 50/50 variety with a bit of silver added to it which is perfectly fine for that hobby but may not be the best for pcb, ics, electronics.
Question5. I also have another product tix anti flux am told this is very good?
I don't know what that is. Anti flux is probably a solution to clean the flux after you solder. This has no importance to what soldering iron you get.
ps. Pace has a series of videos that a beginner like you should watch, they're very helpful :