Author Topic: What is better for bulk capacitor: tantalum, ceramic or aluminum?  (Read 5699 times)

0 Members and 1 Guest are viewing this topic.

Offline alexgTopic starter

  • Regular Contributor
  • *
  • Posts: 90
  • Country: us
What is better for bulk capacitor: tantalum, ceramic or aluminum?
« on: September 16, 2016, 05:56:08 pm »
Hi All, I have a working circuit powered from 3AA batteries that has voltage drop of 500mV on the battery terminals upon load application, everything works okay and in general no complaint, however I want to reduce voltage drop as much as possible and per my understanding that is done by adding bulk capacitance next to battery terminals, due to space limitation I am limited to few choices below:
one tantalum or tantalum polymer of 220uF 6.3V
http://www.digikey.com/product-detail/en/avx-corporation/F930J227MBA/478-8168-1-ND/4005703

two ceramic caps 220uF each X5R 6.3V
http://www.digikey.com/product-detail/en/samsung-electro-mechanics-america-inc/CL32A227MQVNNNE/1276-3375-1-ND/3891461

I also have third option that may work if absolutely necessary, this aluminum polymer cap
http://www.digikey.com/product-detail/en/panasonic-electronic-components/6SVPE220MW/P16836CT-ND/4834392


Which one technically is more suitable for the task?
« Last Edit: September 16, 2016, 06:01:35 pm by alexg »
 

Online tggzzz

  • Super Contributor
  • ***
  • Posts: 19281
  • Country: gb
  • Numbers, not adjectives
    • Having fun doing more, with less
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #1 on: September 16, 2016, 06:14:21 pm »
How much current drop? How long for? What's the highest frequency in the load current?

Remember that Q=I*t=C*V, where I is the current for time t, and V is the voltage drop across a capacitance C.
There are lies, damned lies, statistics - and ADC/DAC specs.
Glider pilot's aphorism: "there is no substitute for span". Retort: "There is a substitute: skill+imagination. But you can buy span".
Having fun doing more, with less
 

Offline T3sl4co1l

  • Super Contributor
  • ***
  • Posts: 21609
  • Country: us
  • Expert, Analog Electronics, PCB Layout, EMC
    • Seven Transistor Labs
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #2 on: September 16, 2016, 06:17:53 pm »
If the lead length between battery and load is short, there isn't much you can do that's better than the battery already.

Tim
Seven Transistor Labs, LLC
Electronic design, from concept to prototype.
Bringing a project to life?  Send me a message!
 

Offline alexgTopic starter

  • Regular Contributor
  • *
  • Posts: 90
  • Country: us
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #3 on: September 16, 2016, 06:24:24 pm »
How much current drop? How long for? What's the highest frequency in the load current?

Remember that Q=I*t=C*V, where I is the current for time t, and V is the voltage drop across a capacitance C.

I will have to measure it later tonight, and report back. Thanks for looking into this.
Actually, I think I remember values, the current drop is 130mA, for 1 second, frequency is 2500Hz,
I will post a waveform later tonight, upon load it drops down, then bouncer up and down within 100mV or so, then comes back up.
« Last Edit: September 16, 2016, 06:32:16 pm by alexg »
 

Offline alexgTopic starter

  • Regular Contributor
  • *
  • Posts: 90
  • Country: us
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #4 on: September 16, 2016, 06:30:03 pm »
If the lead length between battery and load is short, there isn't much you can do that's better than the battery already.

Tim

The length between battery  and load is about 1 inch, it goes from battery to 10V boost regulator and into the load, no long wires between those points. So if I understand correctly, voltage drop cannot be eliminated completely or reduces down to let's say 100mV? Is it a normal number to have .5V voltage drop for 3AA batteries power supply?
 

Offline mikeselectricstuff

  • Super Contributor
  • ***
  • Posts: 13695
  • Country: gb
    • Mike's Electric Stuff
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #5 on: September 16, 2016, 06:35:11 pm »
tant poly or alu. poly will work better than ceramic due to loss of capacitance with DC bias, but will be rather more expensive.
Youtube channel:Taking wierd stuff apart. Very apart.
Mike's Electric Stuff: High voltage, vintage electronics etc.
Day Job: Mostly LEDs
 

Online tggzzz

  • Super Contributor
  • ***
  • Posts: 19281
  • Country: gb
  • Numbers, not adjectives
    • Having fun doing more, with less
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #6 on: September 16, 2016, 06:36:39 pm »
How much current drop? How long for? What's the highest frequency in the load current?

Remember that Q=I*t=C*V, where I is the current for time t, and V is the voltage drop across a capacitance C.

I will have to measure it later tonight, and report back. Thanks for looking into this.
Actually, I think I remember values, the current drop is 130mA, for 1 second, frequency is 2500Hz

I suspected t would be something like that.

So with a 220e-6F capacitor, if you draw 0.13A out of it for 1s, the voltage will fall by 590V :) You're going to need a much much larger capacitor!
There are lies, damned lies, statistics - and ADC/DAC specs.
Glider pilot's aphorism: "there is no substitute for span". Retort: "There is a substitute: skill+imagination. But you can buy span".
Having fun doing more, with less
 

Offline Audioguru

  • Super Contributor
  • ***
  • Posts: 1507
  • Country: ca
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #7 on: September 17, 2016, 01:22:07 am »
Batteries produce DC, not AC. A capacitor filters AC and will have no effect on your DC voltage drop.
I think your batteries are cheap and are no good, or the battery holder connections are bad or your battery current is more than 500mA.
I hope your batteries are not cheap Chinese "Super Heavy Duty" garbage. Energizer AA alkaline cells are good.
 

Offline alexgTopic starter

  • Regular Contributor
  • *
  • Posts: 90
  • Country: us
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #8 on: September 17, 2016, 02:44:58 am »
You were right about bad connections, I connected circuit's input directly to battery terminals and now voltage drop is 140mV, I did keep two 220uF tantalums though, seem to make waveform smoother.
I have a silly question, sorry if it sound completely dumb, what causes voltage to drop, batterie's internal resistance or a load?
 

Offline radar_macgyver

  • Frequent Contributor
  • **
  • Posts: 687
  • Country: us
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #9 on: September 17, 2016, 04:22:54 am »
If it went away when directly connected to the batteries, then most of the voltage drop you saw earlier was due to the series resistance of the interconnecting wire. When directly connected, it would be the internal resistance of the cells.
 

Offline T3sl4co1l

  • Super Contributor
  • ***
  • Posts: 21609
  • Country: us
  • Expert, Analog Electronics, PCB Layout, EMC
    • Seven Transistor Labs
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #10 on: September 17, 2016, 04:30:08 am »
I have a silly question, sorry if it sound completely dumb, what causes voltage to drop, batterie's internal resistance or a load?

Yes and yes.  V=I*R so the drop across the internal resistance is due to current draw.

The time scale matters.  Caps are only good for voltage sag in the microseconds range.  Batteries are good for voltage sag in the hours... :P

Tim
Seven Transistor Labs, LLC
Electronic design, from concept to prototype.
Bringing a project to life?  Send me a message!
 

Offline Brumby

  • Supporter
  • ****
  • Posts: 12288
  • Country: au
Re: What is better for bulk capacitor: tantalum, ceramic or aluminum?
« Reply #11 on: September 17, 2016, 05:07:03 am »
I have a silly question, sorry if it sound completely dumb, what causes voltage to drop, batterie's internal resistance or a load?

Yes and yes.  V=I*R so the drop across the internal resistance is due to current draw.

This  ^  ^  ^
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf