Author Topic: Warming up electronics after shipping in winter ?  (Read 2995 times)

0 Members and 1 Guest are viewing this topic.

Offline lordvader88Topic starter

  • Frequent Contributor
  • **
  • !
  • Posts: 935
  • Country: ca
Warming up electronics after shipping in winter ?
« on: March 14, 2019, 06:45:27 am »
When I've gotten things like motherboards and videocard's delivered in the winter at well below freezing, I've let the sit for a while to warm up and not have water condensing on them and hopefully not mechanically stress anything.

Anyone else cautious like that ? Should I do it with an LCD monitor too ?
 

Offline Ranayna

  • Frequent Contributor
  • **
  • Posts: 856
  • Country: de
Re: Warming up electronics after shipping in winter ?
« Reply #1 on: March 14, 2019, 07:19:29 am »
Anything so cold that you can feel condensation even on the packaging will sit at home for at least a day.
Do not put it directly next to the heater ;)

Regarding fast temperature changes, a small anecdote: In the winter, when I open the window of my bedroom, where also the computer is located, I always hear sometimes really loud cracking sounds from my monitors. I usually open the window in the early morning, to get up better, so the computer is turned off.
After several years doing this, the sound still makes me wonder, but so far nothing broke.
 

Offline med6753

  • Super Contributor
  • ***
  • Posts: 11313
  • Country: us
  • Tek nut
Re: Warming up electronics after shipping in winter ?
« Reply #2 on: March 14, 2019, 12:08:06 pm »
Over this past winter I took delivery of a Siglent SDM3055 and a Fluke 8810A. Both of them were freezing cold from sitting in cold warehouses and delivery trucks. I let them sit for about an hour at room temperature before powering up. But even so it took a good 2 to 3 days of simply powered on idling before they really stabilized.
An old gray beard with an attitude.
 

Offline OwO

  • Super Contributor
  • ***
  • Posts: 1250
  • Country: cn
  • RF Engineer.
Re: Warming up electronics after shipping in winter ?
« Reply #3 on: March 14, 2019, 12:31:01 pm »
Probably inconsequential compared to the thermal stress during reflow. The only thing I would be careful about is condensation. I would say it's fine to put it on top of the heater, warm it up, check for condensation, and power it on.
Email: OwOwOwOwO123@outlook.com
 

Offline Ice-Tea

  • Super Contributor
  • ***
  • Posts: 3063
  • Country: be
    • Freelance Hardware Engineer
Re: Warming up electronics after shipping in winter ?
« Reply #4 on: March 14, 2019, 12:43:16 pm »
Not everything insde the assembly passes through reflow. Don't put it on a heater.

Offline KJDS

  • Super Contributor
  • ***
  • Posts: 2442
  • Country: gb
    • my website holding page
Re: Warming up electronics after shipping in winter ?
« Reply #5 on: March 14, 2019, 07:14:47 pm »
Caps on old IEC mains sockets with the built in filter were the most likely thing to suffer. Always stank when they blew

Offline Neilm

  • Super Contributor
  • ***
  • Posts: 1545
  • Country: gb
Re: Warming up electronics after shipping in winter ?
« Reply #6 on: March 14, 2019, 07:57:33 pm »
If you are looking at test gear I would definately allow it to settle. I have seen units that spec 12 hours recovery after shipping before powering up. It does resolve to 100 atto-amps though.
Two things are infinite: the universe and human stupidity; and I'm not sure about the the universe. - Albert Einstein
Tesla referral code https://ts.la/neil53539
 

Offline electromotive

  • Regular Contributor
  • *
  • Posts: 87
  • Country: us
Re: Warming up electronics after shipping in winter ?
« Reply #7 on: March 14, 2019, 08:07:36 pm »
Due to breathing issues, I keep the humidity in my house somewhat high. I always let hardware acclimate to the house temperature and humidity before use. No less than 24 hours. More than that is overkill here in Ohio, USA.
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf