Author Topic: Very high current >50-100 Amps 3-5 VDC Solid state relay form "C" MBB  (Read 634 times)

0 Members and 1 Guest are viewing this topic.

Offline HCT203

  • Newbie
  • Posts: 4
  • Country: us
Seeking help in finding a source or maybe designing a  high current solid state relay   SPDT  > 50-100 ADC  form  " D"  it is essentially a  form "C" EXCEPT  MBB ( make before break ) working voltage 3-5 V
switching speed < 10 msec  rep rate less than 5/minutes or  every 12 second . seeking very low ON impedance  ( Less than  2 milliohms )
Willing and able to compensate anyone helping  me in solving successfully this requirement .
Please do not underestimate this project will require serious  solid state relay experience as well very strong FET Gate driving design skill,
Been looking to use HT0440 by Microchip , as well as sub-milliohm Power MosFET such as IRF1324S-7PPbF  or IPT004N03L .  
 

Offline Ice-Tea

  • Frequent Contributor
  • **
  • Posts: 776
  • Country: be
    • Freelance Hardware Engineer
Re: Very high current >50-100 Amps 3-5 VDC Solid state relay form "C" MBB
« Reply #1 on: October 16, 2017, 06:35:20 PM »
The problem with devices such as that Microchip is that they are slow. Which means slow switching and spending a looooong time in the Ohmic region of those fets. I made a 80V/30A(+) SSR some time ago that worked fine (albeit not in SPDT form). Should probably work, but depending on your price target it may not be suitable.
An engineer never has a problem. He just needs more time.

FS: LeCroy SDA100G (50GHz and 20GHz + TDR module availble), Chroma 6304 + 2 x 63006, TTi TSX1820P, Yokogawa DL9240L (4ch 1.5GHz), TDS754D, Infinium 54815A, 54825A,R&S CMU 200, HP 8560E with tracking gen
 

Online T3sl4co1l

  • Super Contributor
  • ***
  • Posts: 9546
  • Country: us
  • Expert, Analog Electronics, PCB Layout, EMC
    • Seven Transistor Labs
Seven Transistor Labs, LLC
Electronic Design, from Concept to Layout.
Need engineering assistance? Drop me a message!
 

Online nctnico

  • Super Contributor
  • ***
  • Posts: 13285
  • Country: nl
    • NCT Developments
Re: Very high current >50-100 Amps 3-5 VDC Solid state relay form "C" MBB
« Reply #3 on: October 17, 2017, 04:59:28 AM »
This shouldn't be too hard to design unless there are complicating requirements which make the design difficult (cost, form-factor, rush-in current, etc). However my first thought would be to use a regular relay and be done with it. At 100A a 2 milli-Ohm resistance will dissipate 20W.
There are small lies, big lies and then there is what is on the screen of your oscilloscope.
 

Offline PeterN

  • Newbie
  • Posts: 1
  • Country: au
Re: Very high current >50-100 Amps 3-5 VDC Solid state relay form "C" MBB
« Reply #4 on: December 26, 2017, 12:05:46 PM »
Hi HCT203,
Did you solve your problem? Mind sharing how and what the application was?
If not I could point out a few components that we found useful for designing this type of high current switch.
Peter
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf