Products > 3D printing
3D Printer yet?
Zucca:
annnd I am back....
Finally my Ender5 is back up and running after the relocation to USA.
A few updates.... and gotchas....
remember this problem I had?
--- Quote from: Zucca on February 07, 2021, 06:34:41 pm ---My cooler part fan sporadically does not work, it has nothing to do with the new fan installed.
I saw the problem also before.
--- End quote ---
well this is why...
It drove me crazy for months... now it looks like it is fixed.... double finger crossed....
I had to deactivate the speaker function in Marlin....
If you design a part cooler fan holder.... like I did... see here... print TWO copies... so if one melts down (other story)... then you have a spare to continue to print.
Zucca:
BTW we made it... we are famous!
https://teachingtechyt.github.io/calibration.html#steppers
in the middle of the page
link to here
mnementh:
I recently had a forum member ask aboot a 3DP part for the Datalogging IR Transceiver for the Fluke 87-IV/187/189; in response, I whipped up this quick little universal bracket to fit my Benchtop Meter Stand and updated my post in the Replacement Knobs, Feet and Fittings for Test Equipment thread. It provides a 30mm x 50mm flat plate one can use to attach either the OEM IR Module or your own homebrew module with double-faced foam mounting tape or adhesive-backed Velcro strips.
It is bundled together with the correct version of the meter stand in the zip file linked here:
https://www.eevblog.com/forum/testgear/replacement-knobs-feet-and-fittings-for-test-equipment/?action=dlattach;attach=1298407
For strength, both parts should be printed 0.20-0.16LH, laying flat on largest flat surface (back of Meter Stand, front face of IR Adapter bracket), and with infill set to yield a grid pattern with 1-1.5mm spacing. Both parts will print well with no supports.
Cheers!
mnem
*3DP-ily*
mnementh:
--- Quote from: Zucca on October 13, 2021, 02:05:45 am ---annnd I am back....
Finally my Ender5 is back up and running after the relocation to USA.
A few updates.... and gotchas....
remember this problem I had?
--- Quote from: Zucca on February 07, 2021, 06:34:41 pm ---My cooler part fan sporadically does not work, it has nothing to do with the new fan installed.
I saw the problem also before.
--- End quote ---
well this is why...
It drove me crazy for months... now it looks like it is fixed.... double finger crossed.... I had to deactivate the speaker function in Marlin....
If you design a part cooler fan holder.... like I did... see here... print TWO copies... so if one melts down (other story)... then you have a spare to continue to print.
--- End quote ---
Or a spare printer. >:D Huh... so you found a actual bug, ehhh? :-+
Nice; you designed your own 'fang. But uhhh... what are the two little rectangular nozzles side x side?
mnem
:-/O
Zucca:
--- Quote from: mnementh on October 15, 2021, 12:29:26 am ---Nice; you designed your own 'fang. But uhhh... what are the two little rectangular nozzles side x side?
mnem
:-/O
--- End quote ---
hi mnem, honestly no idea. I tool one 'fang that I liked and fittted to my needs. It prints well PLA. Done for now.
Hoping that TPU will als obe no problem. I will cross the bridge once I'll see it.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version