| Electronics > Beginners |
| My purchase list for my new lab -- budget $1000+, thoughts? |
| << < (29/47) > >> |
| Raj:
Forget wall warts and crimper and helping hands you'll need a good power supply first. |
| AnyNameWillDo:
--- Quote from: ez24 on July 30, 2018, 04:46:41 pm --- --- Quote from: AnyNameWillDo on July 30, 2018, 12:55:48 pm ---Perhaps additional wire too of a certain gauge? --- End quote --- My go to wire is 18 ga stranded silicon. My guess most use smaller wire, ie 20 ga I also use wire assortments from Harbor Freight and Amazon --- End quote --- I believe your guess is correct (I think) -- the datasheet suggests suggests it's 20 AWG: https://media.digikey.com/pdf/Data%20Sheets/Pomona%20PDFs/3782.pdf "Wire: 20 AWG, stranding 41 x 36 t.c., PVC insulated 2.21 (.087) O.D" However what confuses me is that the datasheet says it's rated for 5 amps: "Current: 5 Amperes Cont. " ...and yet when I look up the current limitations (from what I can tell, the "ampacity") for each gauge (for copper) online here http://www.powerstream.com/Wire_Size.htm it says 20 AWG has a max transmission of like 1.3 amps. I'm probably missing something / will have to research more on how to get the ratings for different wires. |
| nanofrog:
--- Quote from: AnyNameWillDo on July 30, 2018, 02:09:48 am ---What crimping tools / crimp connectors do you think are worth looking into? Or are a variety of tools needed for a variety of situations? --- End quote --- Easy enough to manage if using insulated terminals (red, blue, yellow), as you can decent crimpers for this without blowing $500+ for the tool (die nests use the same color code as the terminals). Some non-insulated too. Otherwise this gets very expensive, very quickly. |
| AnyNameWillDo:
--- Quote from: nanofrog on July 30, 2018, 07:24:27 pm --- --- Quote from: AnyNameWillDo on July 30, 2018, 02:09:48 am ---What crimping tools / crimp connectors do you think are worth looking into? Or are a variety of tools needed for a variety of situations? --- End quote --- Easy enough to manage if using insulated terminals (red, blue, yellow), as you can decent crimpers for this without blowing $500+ for the tool (die nests use the same color code as the terminals). Some non-insulated too. Otherwise this gets very expensive, very quickly. --- End quote --- I think I remember seeing something like that here: https://www.amazon.com/Titan-Tools-11477-Ratcheting-Terminal/dp/B0069TRKJ0/ Had a red/yellow/blue color marking in the jaws. Not sure yet what the differences are. Is this an example of such a crimper? |
| ez24:
--- Quote from: AnyNameWillDo on July 30, 2018, 06:39:23 pm --- .. it says 20 AWG has a max transmission of like 1.3 amps. --- End quote --- When I hear "transmission", I think of 100s of feet. Keep in mind that the current rating of good breadboards is 2 amps. Even at 1 meter, the voltage drop at 2a is very small. Try the calculator. I had no trouble running 5a through 18 inch leads. FYI the AN8008 leads could not. If you going to run higher amps then a thicker wire might be more useful. When I made up my leads, I made a lot of 16 ga with alligator clips. Like someone else said, I have never used them. Mini grabbers with 18 ga is what I use. |
| Navigation |
| Message Index |
| Next page |
| Previous page |