| Electronics > Beginners |
| Odd output from Elenco XP-15K Power Supply |
| (1/9) > >> |
| tomherrick:
Bought the kit and put it together yesterday. First step afterward was to check the VDC output. When the pot was turned all the way up to the 15V mark I got -0.53V. Yup, negative. When I turn it all the way back to zero Volts it reads -0.65. Voltage across P2/P1 reads 17VAC; same reading across P2/P3. When I unplug the unit, the LED slowly dims to off and the multimeter value dropped from -0.65 to -0.32 over the course of a minute or so and continues to drop very slowly. I've been over and over the instructions and rechecked the following: polarity of the diodes, caps and LED; output connections from the transformer to P1, P2 and P3; ensured that the regulator was oriented properly. I went through the test procedure and shorted across the output; the unit did not turn off. The error is likely mine and I keep looking past it when I QC my own work... Suggestions??? Thanks. |
| tpowell1830:
Hi Tom, welcome to the forum. Take some very crisp pictures of the board from both sides. Also, a shot of the schematic and post them in another post so that we can see your work and the schematic. You have a size limit for your jpg's (I can't remember what size), but the uploader will complain if they are too big. |
| tomherrick:
Here are photos of the circuit board and the schematic. |
| T3sl4co1l:
Easy enough to inline as well. Click the attachment, right-click the image, copy link. Paste into an img tag: Hah, looks like it's drawn in Multisim of all things. Tim |
| Zero999:
As posted in the other thread: --- Quote from: rstofer on January 21, 2019, 02:16:00 am ---Diodes D5 and D6 make up a poor man's zener diode and the voltage between ground and the point where the diode connects to R4 should read -1.4, give or take. Black wire of you meter goes on ground. This negative voltage is what allows the regulator to get down to 0V. I don't know the AC voltage between the blue and yellow wires of the transformer but about 1.4 times that value should be measured at pin 3 of the LM317 as a DC voltage. Pin 1 of the LM317 should move between some negative value, like -1.4V, up to some positive value, nearly 15V, but I haven't calculated the exact range. --- End quote --- Yes, this is a classic way of getting near 0V from the LM317, which can normally only go down to 1.25V. It could be a problem with the potentiometer. --- Quote from: tomherrick on January 20, 2019, 10:22:44 pm ---Bought the kit and put it together yesterday. First step afterward was to check the VDC output. When the pot was turned all the way up to the 15V mark I got -0.53V. Yup, negative. When I turn it all the way back to zero Volts it reads -0.65. Voltage across P2/P1 reads 17VAC; same reading across P2/P3. When I unplug the unit, the LED slowly dims to off and the multimeter value dropped from -0.65 to -0.32 over the course of a minute or so and continues to drop very slowly. I've been over and over the instructions and rechecked the following: polarity of the diodes, caps and LED; output connections from the transformer to P1, P2 and P3; ensured that the regulator was oriented properly. I went through the test procedure and shorted across the output; the unit did not turn off. The error is likely mine and I keep looking past it when I QC my own work... Suggestions??? Thanks. --- End quote --- What are the voltages from pin 3 to 0V and pin 1 to 0V? |
| Navigation |
| Message Index |
| Next page |