Author Topic: Please help me identify these components!  (Read 841 times)

0 Members and 1 Guest are viewing this topic.

Offline WyverntekGameRepairsTopic starter

  • Regular Contributor
  • *
  • Posts: 118
  • Country: us
  • MAKE: My Day
Please help me identify these components!
« on: January 09, 2020, 01:48:25 am »
Hey there, so I’m not good with lasers and tube technology as of yet, but these look like lasers. They have a manufacture date code of January 1992. The numbers that stand out the most to me is LGR 7655. I looked it up and found lasers, but they were a totally different construction and date. Can someone help me identify the details of these components? A data sheet would be fantastic! Google is currently failing me.
Thank you!

Also, I held them so you could get an idea of the size.
-Sterling Ordes
Wyverntek Game Repairs
(Business License Pending)
 

Offline StillTrying

  • Super Contributor
  • ***
  • Posts: 2850
  • Country: se
  • Country: Broken Britain
Re: Please help me identify these components!
« Reply #1 on: January 09, 2020, 02:04:45 am »
Neon Helium Lasers according to the tech site ebay. ???
.  That took much longer than I thought it would.
 
The following users thanked this post: WyverntekGameRepairs, tebbybabes

Offline james_s

  • Super Contributor
  • ***
  • Posts: 21611
  • Country: us
Re: Please help me identify these components!
« Reply #2 on: January 09, 2020, 02:04:57 am »
Those are helium-neon laser tubes, almost certainly the common 632.8nm red at about 0.5mW in good health. Small tubes like those were commonly used in handheld barcode scanners back before visible diode lasers became available.

They have some value to the right person, a direct emission diode can't touch the beam quality or wavelength stability of a gas laser.
 
The following users thanked this post: WyverntekGameRepairs, tebbybabes

Offline WyverntekGameRepairsTopic starter

  • Regular Contributor
  • *
  • Posts: 118
  • Country: us
  • MAKE: My Day
Re: Please help me identify these components!
« Reply #3 on: January 09, 2020, 04:13:40 am »
Those are helium-neon laser tubes, almost certainly the common 632.8nm red at about 0.5mW in good health. Small tubes like those were commonly used in handheld barcode scanners back before visible diode lasers became available.

They have some value to the right person, a direct emission diode can't touch the beam quality or wavelength stability of a gas laser.

Hm, quite interesting. I’ll need to see if I can get a proper driver for it. I think I know where to  acquire them, but just in case, anyone is welcome to post links to listings of driver boards for this laser tube.

Also... .5mW? These have .64 and .65 mW written directly on them!
-Sterling Ordes
Wyverntek Game Repairs
(Business License Pending)
 

Offline james_s

  • Super Contributor
  • ***
  • Posts: 21611
  • Country: us
Re: Please help me identify these components!
« Reply #4 on: January 09, 2020, 05:38:11 am »
The power supplies are usually potted bricks, for small tubes like that the voltage will be around 1200V at a few mA. Those labels certainly suggest that was the measured power at some point. Sam's laser FAQ is a goldmine of information.

https://www.repairfaq.org/sam/lasersam.htm
 
The following users thanked this post: WyverntekGameRepairs

Offline Gyro

  • Super Contributor
  • ***
  • Posts: 10174
  • Country: gb
Re: Please help me identify these components!
« Reply #5 on: January 09, 2020, 10:22:03 am »
...

Also... .5mW? These have .64 and .65 mW written directly on them!

They are 0.5mW nominal. The figures written on them are what they actually achieved on test. There are manufacturing variances and the light output will drop over the life of the tubes.

The power supply needs to supply around [Edit: several kV] at a few uA for the tubes to 'strike', they then drop to a lower operating voltage at the rated current when running. (just like neon bulbs but at a higher voltage). This is often achieved with a voltage multiplier where the capacitors in the later stages are too low in value to maintain the high voltage at running current.

Laser tubes also require a ballast resistor very close to the Anode (within about 50mm) to operate correctly, they are often built into the tube housing but with bare tubes, you need to provide it.


P.S. The datasheet is pretty easy to find on the web, here's the manufacturer page: https://www.lambdaphoto.co.uk/lasos-lgr-7655-he-ne-laser-tube.html and I've attached the datasheet below (it's a 0.6mW tube).
« Last Edit: January 09, 2020, 10:41:31 am by Gyro »
Best Regards, Chris
 
The following users thanked this post: WyverntekGameRepairs


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf