Author Topic: EEVblog #1163 - Xmas Mailbag  (Read 9216 times)

0 Members and 1 Guest are viewing this topic.

Offline EEVblogTopic starter

  • Administrator
  • *****
  • Posts: 37661
  • Country: au
    • EEVblog
EEVblog #1163 - Xmas Mailbag
« on: December 24, 2018, 09:40:01 pm »


Xmas Mailbag

SPOILERS:
Mand Labs electronics learning kit:
https://mandlabs.com/
27:08 Petzl climbing harness
33:20 RC2014 home brew DIY Z80 computer kit
https://rc2014.co.uk/
https://www.tindie.com/products/Semachthemonkey/rc2014-pro-homebrew-z80-computer-kit/
39:00 Custom test leads
40:40 Aircraft 121.5MHz emergency beacon and altitude sensor teardown
51:30 Monero miner, and some Linux GPL hate!
 
The following users thanked this post: SeanB, s8548a, nuclearcat

Offline tineibous

  • Newbie
  • Posts: 6
  • Country: br
Re: EEVblog #1163 - Xmas Mailbag
« Reply #1 on: December 24, 2018, 10:28:31 pm »
Hey dave at 05:33 you said they sent a acqua blue leds to you, could you show a close up of them to us? Like they glowing and off pls?
 

Offline SeanB

  • Super Contributor
  • ***
  • Posts: 16272
  • Country: za
Re: EEVblog #1163 - Xmas Mailbag
« Reply #2 on: December 24, 2018, 10:30:23 pm »
Polyurethane hydrolysis is common, and will fail any polyurethane plastic within 5 years for the cheap stuff, and 10 years for the better stuff. Keeping it in a dark place and humid makes it worse. Same thing for fall arrestors, they have an expiry date as well, because of the built in frangible section of the main webbing strap, that tears out a sewn section of web, to absorb in a controlled manner, the fall energy and stop you slowly with only minimal risk of injury.

Funny enough the same applies for hard hats, if they are over 5 years old they should be replaced, the plastic they are made from loses plasticisers and gets brittle.
 

Offline EEVblogTopic starter

  • Administrator
  • *****
  • Posts: 37661
  • Country: au
    • EEVblog
Re: EEVblog #1163 - Xmas Mailbag
« Reply #3 on: December 24, 2018, 10:47:19 pm »
Hey dave at 05:33 you said they sent a acqua blue leds to you, could you show a close up of them to us? Like they glowing and off pls?

Maybe on the 2nd channel, or just a photo, remind me.
 

Offline tsman

  • Frequent Contributor
  • **
  • Posts: 599
  • Country: gb
Re: EEVblog #1163 - Xmas Mailbag
« Reply #4 on: December 25, 2018, 12:19:51 am »
A Monero miner installer that is difficult to remove sounds far too much like malware to me.

The mysterious screw + nut is from the gauge adjustment slot on the wire strippers.
« Last Edit: December 25, 2018, 12:22:40 am by tsman »
 

Offline nuclearcat

  • Supporter
  • ****
  • Posts: 382
  • Country: lb
Re: EEVblog #1163 - Xmas Mailbag
« Reply #5 on: December 25, 2018, 12:39:10 am »
It is not suspicious, it is alarming red bad, letter look like one big scriptkiddie attempt to distract Dave and lure to install this crap.
My guess he doesn't know Dave at all, IMHO, it was supposed to trigger Dave, so in rage he plug USB(and get infected) and start to protect fiercely Linux or 1070ti (while it is known for all viewers - he doesn't give a shit on both points).
« Last Edit: December 25, 2018, 12:58:38 am by nuclearcat »
 

Offline Mr. Scram

  • Super Contributor
  • ***
  • Posts: 9810
  • Country: 00
  • Display aficionado
Re: EEVblog #1163 - Xmas Mailbag
« Reply #6 on: December 25, 2018, 01:05:23 am »
It seems some of the past few videos have been much blurrier or less sharp than they should be for a given resolution. More specifically, it seems to be the head shot in the mailbag videos. I assume you recorded them together, so a rogue setting may have impacted more than video?
 

Offline boffin

  • Supporter
  • ****
  • Posts: 1027
  • Country: ca
Re: EEVblog #1163 - Xmas Mailbag
« Reply #7 on: December 25, 2018, 02:40:34 am »
I'm impressed that the RC2014 is RFC2795 compliant.  I only thought it was only my last employer that was fully 2795 compliant.

 
The following users thanked this post: blueskull

Offline johnlsenchak

  • Frequent Contributor
  • **
  • !
  • Posts: 399
  • Country: us
  • js@antihotmail.com
    • paypal.me/johnsenchak
Re: EEVblog #1163 - Xmas Mailbag
« Reply #8 on: December 25, 2018, 04:55:49 am »
He asks  " what is this nut doing here" You're  the guy  with the Dundee  Knife !  LOL

You should  have wrapped up that "Mand Labs electronics learning kit"   and  gave it to Sagan  as a Christmas gift ,that's if he  goes in that direction as
a  hobby .  No , I  don't think  he  would understand all that electronic  theory  at his  age, I started the theory  around  the age of  13

That Mand Labs  kit  is  way  better then those  Radio  Shack  "All in one" kits  that I  learned   on as a teenager

Those Indian  guys real suck ,  they  sound like the scammers   that call me all the time   :-DD
John Senchak "Daytona  Beach  Florida "
 jls (at)  antihotmail.com   http://www.antihotmail.com
https://www.facebook.com/john.senchak.1
 

Offline chickenHeadKnob

  • Super Contributor
  • ***
  • Posts: 1054
  • Country: ca
Re: EEVblog #1163 - Xmas Mailbag
« Reply #9 on: December 25, 2018, 07:07:39 am »
Since you asked for viewer opinion re: mand labs content let me offer my dissenting contrarian voice to your conclusions. When I was in the age range 9-14 I would have been overjoyed to get just the mand lab book. In particular when I was 9 years old I accidentally discovered a book about nuclear physics at the local library. It was intentioned for mid-teenager age range and started with some pictures of the Bohr model (planetary style) atoms. I found it utterly fascinating and it changed my life. I was the youngest member of a STEM-academically oriented family and everyone figured I was the dumbest and not headed for that type of career. Instead after devouring that book it switched me " on"  and I became a voracious consumer of any  technical non-fiction and top of the class star pupil.

OK, I was a weird kid and eventual classic math-science nerd, but even for those that aren't so inclined they know how to skip over the few pages /video scenes of theory and equations to get to the hands on "good" stuff".  I found your over-dubbing you-tube rant type commentary on top of the mand video some of the most annoying minutes of video you have ever produced. If you want us to judge the mand product shut up for 10 seconds and let us watch and listen!. I came away with a much better impression of the mand people and a much lessor one of you.

well you had to ask for our opinion. >:D
 

Offline HighVoltage

  • Super Contributor
  • ***
  • Posts: 5453
  • Country: de
Re: EEVblog #1163 - Xmas Mailbag
« Reply #10 on: December 25, 2018, 12:34:05 pm »
Indeed a very nice kit the mand labs, I would have loved it as a kid, especially the book!
My first electronics book was called "Radiobasteln für Jungen" from 1970.

There are 3 kinds of people in this world, those who can count and those who can not.
 

Offline johnlsenchak

  • Frequent Contributor
  • **
  • !
  • Posts: 399
  • Country: us
  • js@antihotmail.com
    • paypal.me/johnsenchak
Re: EEVblog #1163 - Xmas Mailbag
« Reply #11 on: December 25, 2018, 12:49:43 pm »


I  started  electronic  theory  with the Radio Shack " DC  and  AC Circuits - Basic Circuit Concepts "  The red and blue  four  books.

The problem is with  the A/C  theory  you needed algebra/trigonometry  to understand the concepts  which  most grade  school kids  don't have
John Senchak "Daytona  Beach  Florida "
 jls (at)  antihotmail.com   http://www.antihotmail.com
https://www.facebook.com/john.senchak.1
 

Offline DL3CE

  • Newbie
  • Posts: 6
  • Country: de
Re: EEVblog #1163 - Xmas Mailbag
« Reply #12 on: December 25, 2018, 01:06:35 pm »
Quote
My first electronics book was called "Radiobasteln für Jungen" from 1970.
That book had a whole lot of editions, I think the first one was 1955(?) and there were predecessors. The older editions used valve circuits connected directly to the mains quite often, and I don't remember any (serious) warnings about the possibly live chassis. :o

The Mand Labs kit made me look into the current state of electronics kits for kids and .. I'm shocked how pathetic they got. Nothing compared to those I had in my youth and they already were on their downfall back then. Relatives often gifted me new ones up to my 11-12th birthday or so (after that I got my first soldering iron and some Veroboard) and the newer ones got more and more in the direction of cheap toy and stripped the really cool projects. This kit is a step in the right direction, but they don't seem to have deceided if they want to target elementary school kids or college students, the complexity of the explanations is all over the place somehow?

With the older ones you could build amplifiers, tone controls .. and there was even one for a functional television! And they explained everything .. they weren't mathurbating of course, but more in "Art of Electronics"-style: "This transistor does that and its operating point is stabilized via this DC feedback .. "

If I ever have kids, I think I would be looking for an NOS one or create one myself. Basic electronics didn't change THAT much in the last decades, a transistor amplifier is still made the same way it was in the 1960ies.

 

Offline timgiles

  • Regular Contributor
  • *
  • Posts: 236
  • Country: se
  • Programmer, DB architect
Re: EEVblog #1163 - Xmas Mailbag
« Reply #13 on: December 25, 2018, 02:54:03 pm »
The Mand Kit looked great - at last a well put together quality product that does not break the bank. Sure, there are cheaper products out there, but, the literature alone is worth most of the money. And, I also believe very strongly that children who are going to go in to engineering, comp sci, etc... should have nice things so they can learn to take care, think twice etc... And that kit fits that description.

I think we should lay off the indian chaps a bit. Sure, they speak with an indian accent in not so perfect english, but I doubt many of us can speak any of the many indian languages that there are. Also - at least they have done this! They have actually produced the book(s), the kit, with a serious nood in the direction of quality. Also it is aimed at a younger audience, young uns today do expect a different approach to videos. I doubt there are too many PewDiPie followers out there watching Dave (note I said too many and not any).

Well done to them for sending it in - even though I would suggest they tipped Dave off next time. But Mail bag is mail bag !-) I hope it takes off during 2019 and we can see a few follow on kits come on line in the sam style 2019/20.
 

Offline Mr. Scram

  • Super Contributor
  • ***
  • Posts: 9810
  • Country: 00
  • Display aficionado
Re: EEVblog #1163 - Xmas Mailbag
« Reply #14 on: December 25, 2018, 04:55:23 pm »
I agree with most people here that it's hard to provide too much information. Children may not be able to comprehend it all, but exposing them to it can't hurt and probably even helps. Meanwhile they can pick up the parts they do understand. Exposing yourself to things you don't understand yet is a classic way of learning something complicated. Even just having heard of some of the more technical terms can massively help later on, and some will just run with it.

Both the Indian accent and the video presentation may be a bit of an issue. Most children grow up learning English, but combined with the unfamiliar accent it may be a bit too much. It's not about whether we speak the many Indian languages and dialects, it's about whether the children viewing the video will have trouble with it. It's fairly obvious the pair presenting the video aren't very accustomed to that, making the video less engaging and clear than it could have been. It's not a total disaster, but it does seem to be the roughest part of an otherwise rather polished and well-made product.
 

Offline timelessbeing

  • Frequent Contributor
  • **
  • Posts: 929
  • Country: 00
Re: EEVblog #1163 - Xmas Mailbag
« Reply #15 on: December 26, 2018, 12:04:22 am »
So what was that thing you couldn't tell us in the Youtube video? You can say it here right? Are you live streaming somewhere else?
 

Offline jonovid

  • Super Contributor
  • ***
  • Posts: 1425
  • Country: au
    • JONOVID
Re: EEVblog #1163 - Xmas Mailbag
« Reply #16 on: December 26, 2018, 12:18:35 am »
Mand Labs electronics learning kit: their still learning  :-DD truly cringeworthy Mand Labs video,  :clap: a thousand apologies for the thick accent :palm: why Dave you need to do the video for them.
and redesign their kit for them , maybe add your own DMM and more electronic components.
Hobbyist with a basic knowledge of electronics
 

Offline NiHaoMike

  • Super Contributor
  • ***
  • Posts: 8972
  • Country: us
  • "Don't turn it on - Take it apart!"
    • Facebook Page
Re: EEVblog #1163 - Xmas Mailbag
« Reply #17 on: December 26, 2018, 05:38:35 am »
I have no problems with the accent, but I agree they start out with too much history and theory. The format I suggest to start with basic information on how to use the component, with the history and theory part moved to optional "learn more" sections.
Cryptocurrency has taught me to love math and at the same time be baffled by it.

Cryptocurrency lesson 0: Altcoins and Bitcoin are not the same thing.
 

Offline Smokey

  • Super Contributor
  • ***
  • Posts: 2536
  • Country: us
  • Not An Expert
Re: EEVblog #1163 - Xmas Mailbag
« Reply #18 on: December 26, 2018, 06:59:03 am »
Watch this video from a company that makes climbing gear:
https://dmmclimbing.com/Knowledge/September-2013/Slings-at-Anchors

Saying your gear doesn't need to be rated for falls if you are only canyoneering and rappelling is just not true.  If things go sideways (and they will go sideways at some point) you can still pretty easily generate enough force to break your gear (and anchors), or your back.  Even if your gear is brand new.  I've found that canyoneers that are not also rock climbers have a poor understanding of this stuff.

One big problem is static links in the system.  This includes static ropes (no stretch), static cord, and sewn static slings.  These are all used to attach yourself to an anchor or other rigging/rope system.  A falling body generates high forces much faster than you would imagine and theses static links transmit those forces straight to the linkages (carabiners, etc) and your body (spine, organs).

Because they are typically only rappelling, canyoneers often use static ropes (ie they don't stretch like normal climbing ropes).  Even if you do use dynamic ropes that stretch, you are still using other static elements like cords and slings at various times like when attached to an anchor waiting to rappel.  This disastrous situation can easily happen when clipping into a hanging anchor waiting to rappel and slipping with slack in the system.

From the video:
For an 80kg mass and 120cm dynema sling...
.....fall factor 1 falls (falling from the height of the anchor) generated 16kN.
.....fall factor 2 falls (falling from above the anchor) generated 27kN.

For some gear references:
... A typical anchor carabiner might be rated at 25kN (major axis, gate closed)
"Black Diamond Positron Screwgate Locking Carabiner"
https://www.rei.com/product/899070/black-diamond-positron-screwgate-locking-carabiner
... and a dynema sling rated at 22kN
"Black Diamond 10mm Dynex Runner",
https://www.rei.com/product/899001/black-diamond-10mm-dynex-runner

So as shown in the video, the above listed fall factor 2 breaks brand new gear.  What if the carabiner got turned sideways?  It's only good to 8kN now and broken in less than a fall factor 1.

..... and this all ignores the fact that you will have serious internal injuries (broken pelvis, busted organs, etc) at around a 12kN shock.

So ya, even canyoneering gear needs to be fall rated (and you need to be really careful to avoid static falls!!).
« Last Edit: December 26, 2018, 07:01:12 am by Smokey »
 
The following users thanked this post: mtdoc, thm_w

Offline FrankBuss

  • Supporter
  • ****
  • Posts: 2365
  • Country: de
    • Frank Buss
Re: EEVblog #1163 - Xmas Mailbag
« Reply #19 on: December 26, 2018, 07:45:05 am »
Indeed a very nice kit the mand labs, I would have loved it as a kid, especially the book!
My first electronics book was called "Radiobasteln für Jungen" from 1970.

Right, girls don't tinker with electronics :palm:

I started with a Kosmos Elektronik kit when I was young, and I remember later reading the very good book "Einführung in die Elektronik" by Jean Pütz when I was older:



It started with some theory as well, but lots of practical circuits and easy to understand explanations.
So Long, and Thanks for All the Fish
Electronics, hiking, retro-computing, electronic music etc.: https://www.youtube.com/c/FrankBussProgrammer
 

Offline Fungus

  • Super Contributor
  • ***
  • Posts: 16560
  • Country: 00
Re: EEVblog #1163 - Xmas Mailbag
« Reply #20 on: December 26, 2018, 08:13:07 pm »
So ya, even canyoneering gear needs to be fall rated (and you need to be really careful to avoid static falls!!).

How exactly do you "fall" when you're rappelling? All ropes/slings are under tension at all times, no slack.

(if you're doing it right).

 

Offline Smokey

  • Super Contributor
  • ***
  • Posts: 2536
  • Country: us
  • Not An Expert
Re: EEVblog #1163 - Xmas Mailbag
« Reply #21 on: December 27, 2018, 01:22:46 am »
If we could all be 100% sure we were NEVER going to fall/slip/static load anything then why have any gear at all? 
No one wants to make an impact on a static system, but that doesn't mean you aren't in the situation where is can happen pretty often if you or someone else makes a mistake or something happens out of your control.. 
What if you have a wacky anchor (as canyoneers often do) that has long tails to points far from each other.  While starting the rap one of those anchor points (or tails) fails.  That will drop you and the rap rope together until the other side of the anchor catches.  Boom.  Shock load. 
Much more common would be slipping while clipped to an anchor with slack in the system (like standing on a small ledge with the anchor at your waist but not having your teather tight)
People die like that.
 

Offline thm_w

  • Super Contributor
  • ***
  • Posts: 6272
  • Country: ca
  • Non-expert
Re: EEVblog #1163 - Xmas Mailbag
« Reply #22 on: December 27, 2018, 10:18:33 pm »
Watch this video from a company that makes climbing gear:
https://dmmclimbing.com/Knowledge/September-2013/Slings-at-Anchors

Saying your gear doesn't need to be rated for falls if you are only canyoning and rappelling is just not true.  If things go sideways (and they will go sideways at some point) you can still pretty easily generate enough force to break your gear (and anchors), or your back.  Even if your gear is brand new.  I've found that canyoners that are not also rock climbers have a poor understanding of this stuff.

You can tell when the mental gymnastics started, to justify that he knew the harness was good because his buddy owned it, that its not a great idea to use.
A new harness is $75? A new helmet is another 75? To spend that every 5 years or so on a hobby you enjoy is quite reasonable. I would have no problem donating a bit to get some new gear if thats what it took.  :)
Profile -> Modify profile -> Look and Layout ->  Don't show users' signatures
 

Offline Grapsus

  • Regular Contributor
  • *
  • Posts: 242
  • Country: fr
Re: EEVblog #1163 - Xmas Mailbag
« Reply #23 on: December 28, 2018, 01:24:54 pm »
I remember the hate about the GTX 1070 Ti is that it came out just a few tens of dollars more expensive that the 1070 while having almost the performance of a 1080.
So both 1070 owners and 1080 owners felt ripped off. Also everybody was expecting a new architecture instead of a refresh. Gaming hardware circlejerk...

I really don't get the guy's stance on the GPL. Is it cancer ? People who develop stuff for free, let you use and modify it for free dare to impose conditions on commercial use of their work ? The bastards !
 

Offline LapTop006

  • Supporter
  • ****
  • Posts: 467
  • Country: au
Re: EEVblog #1163 - Xmas Mailbag
« Reply #24 on: December 28, 2018, 02:10:52 pm »
I really don't get the guy's stance on the GPL. Is it cancer ? People who develop stuff for free, let you use and modify it for free dare to impose conditions on commercial use of their work ? The bastards !

Not commercial use (that would be more the CC-NC licences, which end up being very restrictive since many things are commercial use that you might not think of at first), but redistribution.

In some ways I guess it's just slightly different direction from the "free software" hardliners (Richard Stallman etc.). The FreeBSD developers I know have always been fairly pragmatic about it.

Personally, if I'm not contributing to an existing project I'll use GPL or CC-BY-SA for content.
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf