General > General Technical Chat
10 mV Differential signal RFI filters
(1/2) > >>
loop123:
I want to avoid building a large Faraday Cage that can costs thousands of dollars. So I plan to just use RFI filters in the differential input stage of my bioamplifiers or any I'd use without any filter to avoid clipping the output or any nonlinear effects. I saw this RFI filter used by Olimex.



https://www.olimex.com/Products/Duino/Shields/SHIELD-EKG-EMG/resources/SHIELD-EKG-EMG.pdf

It uses simply low pass RC filters. Is it already the optimum design? Can you give other designs used in other amplifiers?  How can one add for example ferrite beads into it? My observations:

1. The capacitors in each common mode input must be exact or tolerance of 0.001%. If they differ, it can introduce differential signal. For the differential capacitor. I guess any will do.

2. To look for resistor and capacitor i'll use in both common mode (C2, C3) and differential (C1).  Must I focus on the frequency only and not so much on the voltage? For example. My maximum input is only 10mV. So I can use the same resistor and capacitor in the low pass RC filter used in say 10000V equipment if the frequency cutoff is the same?

3. If the source of the interference is line and radiated. The filter can filter both? My focus is filtering radiated intereference because I only used batteries.

4. Should I look for cutoff in the 1Mhz region or all above 10kHz? What values of resistor and capacitor must I get? One with tolerance of 0.0001% to avoid causing differential signal in the mismatch.

5. In a Faraday Cage. What is the minimum frequency it can allow? Please give picture of an actual table size Faraday Cage. I want to know how opaque it is or transparent and how you insert your hands inside the cage.

Thank you.
David Hess:

--- Quote from: loop123 on February 25, 2024, 11:38:36 pm ---1. The capacitors in each common mode input must be exact or tolerance of 0.001%. If they differ, it can introduce differential signal. For the differential capacitor. I guess any will do.
--- End quote ---

That is definitely a problem.  The solution is usually to make sure that the cutoff frequency of the common mode filter is much higher than the signal bandwidth of interest.  The filter is only used to block radio frequency interference.

Low pass filtering, if required, is implemented *after* the differential to single ended conversion, or with a differential mode filter although this will convert some of the differential signal to common mode reducing common mode rejection.
loop123:

--- Quote from: David Hess on February 26, 2024, 02:24:51 am ---
--- Quote from: loop123 on February 25, 2024, 11:38:36 pm ---1. The capacitors in each common mode input must be exact or tolerance of 0.001%. If they differ, it can introduce differential signal. For the differential capacitor. I guess any will do.
--- End quote ---

That is definitely a problem.  The solution is usually to make sure that the cutoff frequency of the common mode filter is much higher than the signal bandwidth of interest.  The filter is only used to block radio frequency interference.

Low pass filtering, if required, is implemented *after* the differential to single ended conversion, or with a differential mode filter although this will convert some of the differential signal to common mode reducing common mode rejection.

--- End quote ---

Were you referring to C1 (see original figure) in the differential mode filter thing? I know how common mode can convert to differential signal. But how could it "convert some of the differential signal to common mode"?

Also for 1mV to 10mV. What kind of radiated EMI (do you refer EMI only to line intereference or can it be radiated too?) or radiated RFI that is strong enough to disturb the 1mV to 10mV? Does this really happen at all?  What must be the strength of the RFI to cause the 1mV to 10mV to become distorted or clipped like this (it's just example I saw elsewhere, ignore the frequency of the red sine wave):



Supposed the green sine wave (top) is the 1mV signal. And the red sine wave is the RFI (radiated). What strength of the RFI before it can clip the 1mV signal such that the output (at bottom) would become distorted?

I'm talking of radiated RFI interference, not from EMI from power supply lines because I used batteries, so it is disconnected from main.

David Hess:

--- Quote from: loop123 on February 26, 2024, 02:39:06 am ---Were you referring to C1 (see original figure) in the differential mode filter thing? I know how common mode can convert to differential signal. But how could it "convert some of the differential signal to common mode"?
--- End quote ---

I am actually not sure now what I had in mind when I said that.


--- Quote ---Also for 1mV to 10mV. What kind of radiated EMI (do you refer EMI only to line intereference or can it be radiated too?) or radiated RFI that is strong enough to disturb the 1mV to 10mV? Does this really happen at all?  What must be the strength of the RFI to cause the 1mV to 10mV to become distorted or clipped like this (it's just example I saw elsewhere, ignore the frequency of the red sine wave):
--- End quote ---

It could be radiated EMI that gets into the input, or conducted EMI.

What happens is that the RF at the input gets rectified by the input transistors or other active devices which causes a shift in offset voltage.  This is just AM detection.

If there are multiple RF frequencies, then non-linearities in the input stage can mix them to produce low frequency interference.
loop123:

--- Quote from: David Hess on February 26, 2024, 03:06:45 am ---
--- Quote from: loop123 on February 26, 2024, 02:39:06 am ---Were you referring to C1 (see original figure) in the differential mode filter thing? I know how common mode can convert to differential signal. But how could it "convert some of the differential signal to common mode"?
--- End quote ---

I am actually not sure now what I had in mind when I said that.


--- Quote ---Also for 1mV to 10mV. What kind of radiated EMI (do you refer EMI only to line intereference or can it be radiated too?) or radiated RFI that is strong enough to disturb the 1mV to 10mV? Does this really happen at all?  What must be the strength of the RFI to cause the 1mV to 10mV to become distorted or clipped like this (it's just example I saw elsewhere, ignore the frequency of the red sine wave):
--- End quote ---

It could be radiated EMI that gets into the input, or conducted EMI.

What happens is that the RF at the input gets rectified by the input transistors or other active devices which causes a shift in offset voltage.  This is just AM detection.
--- End quote ---

What? can you help illustrate what you mean? did AM means Amplitude Modulation? what detection of AM and how can it exactly cause a shift in offset voltage?


--- Quote ---
If there are multiple RF frequencies, then non-linearities in the input stage can mix them to produce low frequency interference.

--- End quote ---

Does this happen in a typical city with ambient background electromagnetic environment with hundreds of radio stations, tv stations, cellular tower all around, or does the non-linearities only occur when you are directly below a microwave disc, radar or the like? Can someone give examples of actual waveforms of the RFI interferences? If your device has no input filters of any kind. It's totally or almost useless?
Navigation
Message Index
Next page
There was an error while thanking
Thanking...

Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod