I am now living in Germany, where do you Germans send your PCB orders? DANKE!

[Zucca]

Sorry for bombing the Chat Forum so much, but after the success of the components thread here I could not resist, here we go again with the PCB Manufacturing side...

I found these (unfortunately only in German), really well done:
http://www.mikrocontroller.net/articles/Platinenhersteller
http://wiki69.pst69.homeip.net/index.php/Platinenerstellung

Basically I will try to put all your feedbacks here below:

http://www.hegergmbh.com/en/ really good quality PCB's, can even read my PADS files
https://www.haka-lp.de/home.html They do good work, I always got good quality! They accept Target, Eagle and Gerber files.
http://www.wedirekt.de/ specialized on large batches, Good quality, fast, a lot of options and cheaper then expected. The "free" Stencil is not bad at all.
http://www.jlp.de/  Standard small orders
http://www.elekonta.de/ Standard small orders
http://www.leiton.de/ more complicated stuff/material choices
http://www.fischer-leiterplatten.de/ small/private projects
http://www.andus.de/index.en.php VERY FAST, but also VERY Expensive
http://eurocircuits.com/ Their online PCB Visualizer is the special distinguishing feature to all other manufacturers. You can upload your gerber.rar and the PCB Visualizer displays all layers and points to errors. It does a DRC and DFM check and later this year a pre-CAM check.
http://www.seeedstudio.com/service/index.php?r=pcb cheap chinese stuff




Again thank you so much you are amazing.

PS: I promise I will not post anything else with that title.

[HighVoltage]

For really good quality PCB's, I am always ordering here:

http://www.hegergmbh.com/en/

They can even read my PADS files, when many others have problems with that.

[hammy]

I can recommend https://www.haka-lp.de/home.html
They do good work, I always got good quality! They accept Target, Eagle and Gerber files.

[luky315]

I use WEdirect http://www.wedirekt.de/
Good quality, fast, a lot of options and cheaper then expected. The "free" Stencil is not bad at all.

[babysitter]

Q-Print and Fischer-Leiterplatten are my favourites.
(Q-Print has to be, my wife was working there )

[Andreas]

Hello,

where in Germany are you living?
It really makes a difference if you can pick up your PCBs in Berlin or are at the "arse of the world"
Is the PCB for prototypes or series?

If you really need id fast you should consider ANDUS Berlin.
(but dont complain about the price for that service).

Standard small orders I have mostly done at Jenaer Leiterplatten or Elekonta.
http://www.jlp.de/
http://www.elekonta.de/

The already mentioned Würth (wedirekt) is more specialized on large batches.
Delivery time might be (slightly) affected by a fire end of last year in one of their fabs.
http://www.elektroniknet.de/elektronikfertigung/fertigungstechnik/artikel/115929/
http://www.bild.de/regional/stuttgart/stuttgart-regional/grossfeuer-zerstoert-wuerth-werk-39127754.bild.html

If only the price matters and delivery time is no concern you can also order
from one of the chinese manufacturers.

With best regards

Andreas

[Kjelt]

Q: are these firms anywhere price competitive with the chinese pcb manufacturers or are time and "made in Germany" the deciding factors to go with these manufacturers ?

[SCR]

Leiton for more complicated stuff/material choices and Fischer for my private projects

[Zucca]

Thanks Andreas for the Feedback and the good questions

where in Germany are you living?

Munich

Is the PCB for prototypes or series?

99% prototypes, 1% series (well.. about 100-200 pieces...)

Thank you!

[kmel]

Sorry for bombing the Chat Forum so much, but after the success of the components thread here I could not resist, here we go again with the PCB Manufacturing side...

http://eurocircuits.com/
Their online PCB Visualizer is the special distinguishing feature to all other manufacturers.
You can upload your gerber.rar and the PCB Visualizer displays all layers and points to errors.
It does a DRC and DFM check and later this year a pre-CAM check.

Regards,
Klaus

[Zucca]

OP updated.

I was expecting at least one reporting https://oshpark.com/... or the German custom costs (USA-->D) are turning around the biz case?

WOW http://www.pcb-pool.com/ppde/info_pcbpool_rfid.html RF-ID in the PCB?

[nctnico]

I use either Eurocircuits (professional) or Seeedstudio (if it has to be cheap).
Eurocircuits is easy to work with and they are not very expensive. Their are somewhere in Europe but they do meet their delivery dates every time.

[Wh1sper]

Did you ask for some special hobbiest offers, also?
I would have one or may be  two. But I'm not sure if I should advertise here, because I'm in doubt they would have been overrun by the overhelming flood of requests.