General > General Technical Chat

Partially "dead" TVS - diode?

(1/2) > >>

masta_k74:
I have removed a TVS diode from a defective switching power supply unit to check it and when I measure it with my power supply unit @ 32V (current limitation to 50mA and series resistor) it shows the normal value (0.64V) in one direction and a value of 15.6V in the reverse direction, although this diode is specified for 250V according to the datasheet?
When measuring with the DVM, however, the display shows 0.35V in both directions.
Have any of you had similar cases?

The power supply was just pulsating and this TVS reached over 130°C in a few seconds according to the Flir camera.
The TVS was here with some more passive components and a normal diode as a snubber on the primary winding of the transformer.

So far, I have only known complete continuity or completely open with defective diodes / Zener diodes, and a TVS functions more or less like a Zener diode. :-//
Are TVS diodes also subject to an ageing process like varistors?

jonpaul:
partial failure, replace it.

But suspect that the TVS fail is an effect and root cause lies elsewhere


j

thm_w:
Yes, I've seen similar issues before with partial failure, not dead short.
I don't think its aging, seems more likely repeated overload or thermal related, which could indicate another concern.

Whats the part number?

Your measurements are a bit interesting though, 0.35V with the DMM and probably 1mA current. While the power supply is 16V at 50mA. Maybe try to set power supply to 1mA.

timenutgoblin:

--- Quote from: masta_k74 on November 16, 2022, 11:07:02 am ---I have removed a TVS diode from a defective switching power supply unit to check it and when I measure it with my power supply unit @ 32V (current limitation to 50mA and series resistor) it shows the normal value (0.64V) in one direction and a value of 15.6V in the reverse direction, although this diode is specified for 250V according to the datasheet?
When measuring with the DVM, however, the display shows 0.35V in both directions.
Have any of you had similar cases?

The power supply was just pulsating and this TVS reached over 130°C in a few seconds according to the Flir camera.
The TVS was here with some more passive components and a normal diode as a snubber on the primary winding of the transformer.

So far, I have only known complete continuity or completely open with defective diodes / Zener diodes, and a TVS functions more or less like a Zener diode. :-//
Are TVS diodes also subject to an ageing process like varistors?

--- End quote ---

As already mentioned, a typical DMM in the diode range has a test current of 1mA. Also, the open circuit test voltage for a DMM in the diode range is typically 3V, but some DMMs have a higher test voltage such as Fluke 17X (7V) and then there's the EEVBlog 121GW which can be selected between 3V and 15V. (See attachment).

I think your best approach is to use your bench power supply for testing TVS diodes and zener diodes. The fact that your DMM measured 0.35V in both directions is an indication that the TVS has failed in at least one mode of failure.

masta_k74:
Part number of the diode is p6ke250.
The diode is installed in the device (battery charger, designed as a flyback converter) as a snubber on the primary winding of the transformer. As far as I can tell from the traces, there is only one fast switching diode, with opposite polarity, in the signal path. 4 x 400k resistors are connected in parallel across both diodes.
At this point, I have only known snubbers consisting of diode, resistor and capacitor. (Using a TVS for this was unknown to me).
I have not been able to find any other defects, despite a thorough check of the components.

Navigation

[0] Message Index

[#] Next page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod