General > General Technical Chat

Where can I get this stackable header *cheaply*?

<< < (3/4) > >>

HwAoRrDk:

--- Quote from: Buriedcode on March 03, 2024, 12:06:05 am ---https://www.toby.co.uk/board-to-board-pcb-connectors/254mm-sockets/309ae-254mm-elevated-single-and-dual-row-socket-strip/

--- End quote ---

Oh, interesting, thanks. They don't list the variant I want (309AE-40-SG-2Z-1555) though. :( Maybe I should enquire, as their prices are more realistic.


--- Quote from: mikeselectricstuff on March 02, 2024, 10:07:35 pm ---May well be something at LCSC but could be tricky to find it with their sub-optimal search.

--- End quote ---

Oh, believe me, I scoured LCSC from top-to-bottom. They only have two products like it, albeit not the same, with only single layer shrouding: C35165 and C5307344.

NiHaoMike:

--- Quote from: HwAoRrDk on March 02, 2024, 08:27:08 pm ---Nope, nope, and nope. Those are all with a single layer of pin shroud. I'm looking for double layer of pin shroud. I need approx. 13.5mm between the top and the base of the pins, which is what 8.5+(2*2.54) will give. Thanks anyway. :)

--- End quote ---
If the pin length is enough, 3D print some spacers?

jonpaul:
Samtech

https://www.samtec.com/

voltsandjolts:

--- Quote from: HwAoRrDk on March 02, 2024, 08:27:08 pm ---
--- Quote from: oPossum on March 02, 2024, 08:03:04 pm ---https://www.aliexpress.us/item/2251832710322745.html

https://www.aliexpress.us/item/2251832777349207.html

https://www.aliexpress.us/item/3256802129587874.html

--- End quote ---

Nope, nope, and nope. Those are all with a single layer of pin shroud. I'm looking for double layer of pin shroud. I need approx. 13.5mm between the top and the base of the pins, which is what 8.5+(2*2.54) will give. Thanks anyway. :)

--- End quote ---

Please excuse me for being a little slow on the uptake, but don't these almost fit the requirements?
I mean, by sliding on a few extra 'shroud' pieces to the pins at each end, and perhaps in the middle, these would be adequate?
'Shroud' pieces can be slid off of standard pins headers with a bit of persuasion.

HwAoRrDk:

--- Quote from: voltsandjolts on March 03, 2024, 05:10:57 pm ---I mean, by sliding on a few extra 'shroud' pieces to the pins at each end, and perhaps in the middle, these would be adequate?
'Shroud' pieces can be slid off of standard pins headers with a bit of persuasion.

--- End quote ---

An ingenious idea, but one problem: these stackable headers nearly all have 0.64x0.60mm pins (i.e. rectangular) and regular male pin headers are typically 0.64x0.64mm square, so the shrouds would just be all loose.

And anyway, I don't wanna have to do that dozens and dozens of times, nor waste a bunch of male pin header strips. :--


--- Quote from: jonpaul on March 03, 2024, 04:25:27 pm ---Samtech

--- End quote ---

Does no-one actually read the posts in threads any more? ::)

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod