Author Topic: uRuler (Read 265707 times)

krivx · « **Reply #475 on:** November 19, 2013, 11:50:42 am »

Received mine this morning in Ireland.

BBQ · « **Reply #476 on:** November 19, 2013, 12:13:18 pm »

They have arrived!

cg · « **Reply #477 on:** November 19, 2013, 12:24:30 pm »

Today my uRulers arrived to finland. Nothing special on the envelope

Hamster · « **Reply #478 on:** November 19, 2013, 12:50:09 pm »

Received my 5 Rulers , New Port Richey, FL

KD0CAC John · « **Reply #479 on:** November 19, 2013, 02:04:11 pm »

Got my 5 rulers last week , was going to mention here but the BLOG was down

Following the thread on using ruler , will copy when it seems done

Thanks John

fs · « **Reply #480 on:** November 19, 2013, 02:24:24 pm »

Mine arrived on Nov 19th, in Ireland. Thanks!

Maff^ · « **Reply #481 on:** November 19, 2013, 03:19:16 pm »

Received my two rules today (19-11-2013) in the Netherlands!

Legit-Design · « **Reply #482 on:** November 19, 2013, 03:23:09 pm »

Quote from: Legit-Design on November 19, 2013, 10:52:24 am

I went in for a closer look
Bigger picture

The middle one (third from bottom and top), IS FAULTY .
Silkscreen on 2.0mm to 1.4mm is faded. Also text "EEVBLOG.COM µRuler" text has jagged edges for the same reason. When I look really close with good light, I can see it looks like rasterized, with not enough ink. Maybe their machine ran low/out on white ink/silkscreening?

Issue can be clearly seen on that top ruler. Rounded corner.

After playing around all day with my shiny new µRulers (I was doing other things and just fiddling around with them, also I played only with two but all five are the same), I noticed all of my 5 rulers have a notch at the inch measurement end. Measurement end is not straight. Not all corners are exactly the same, some rulers have bigger notch than others, one is almost non existent, if the others didn't have it I wouldn't have noticed. Millimeter start and end are straight, inches start is straight and stop looks like router was badly configured to produce these in a hurry, so it took too much from the end.

Anyone else have this? I doubt it's only my rulers. The faded silkscreen might be more rare issue. Not that it is a huge issue for me, thought I should still report it. Might still be enough to complain to pcb manufacturer for discount on possible new batch?

Switching Power · « **Reply #483 on:** November 19, 2013, 05:16:23 pm »

I got my 5 uRulers today (19-11-2013) in the Netherlands.
And i can also see the very tiny notch on all my rulers like Legit-Design mentioned but that's not a problem.
Tanks Dave

Jeroen3 · « **Reply #484 on:** November 19, 2013, 05:16:52 pm »

The uRules arrived in the Netherlands.
They look perfectly fine.

redtails · « **Reply #485 on:** November 19, 2013, 05:23:53 pm »

Hai guis

I received mine also in Netherlands

Notice the stamp, though maybe it has to be like that

belasajgo · « **Reply #486 on:** November 19, 2013, 06:27:20 pm »

My five µRulers arrived today. Greetings from Romania!

PeterL · « **Reply #487 on:** November 19, 2013, 06:37:13 pm »

Hi Dave,

Received my 5 rulers today in the Netherlands. It took some time, but it was worth the wait.

Thanks,
Peter

ViceSpy · « **Reply #488 on:** November 19, 2013, 06:47:11 pm »

Another one in Finland came today.

Thanks for the rulers and the blog!

Kremmen · « **Reply #489 on:** November 19, 2013, 07:06:13 pm »

...and my 5 rulers too in Finland today (19.11.)

JuKu · « **Reply #490 on:** November 19, 2013, 07:19:47 pm »

I got mine today, envelope looked like ViceSpys' picture. The Australian post label was covered by the sticker; no idea which country they were posted from. (I'm only 200 miles from Sweden, but I don't think they came there.)

kubeek · « **Reply #491 on:** November 19, 2013, 08:18:25 pm »

5 rulers reporting in from Czech republic. With singapore stamp, and a return adress to singapore. Why not, it is just a mere 12000km away

RoelA · « **Reply #492 on:** November 19, 2013, 09:02:46 pm »

Received my uRuler too, Netherlands.. Envelope has some minor damage, the rulers are fine.

calmtron · « **Reply #493 on:** November 19, 2013, 09:26:07 pm »

Received 5 uRulers here (Sweden) today, sent from "DLWW Pty Ltd, Malmo, Sweden".

No problems except some slight warping and a slightly smudged silkscreen on one. Already using them. Thanks!

Stonent · « **Reply #494 on:** November 19, 2013, 09:29:39 pm »

I was one of the people contacted later into this that was told that my address was not on file, despite me already being aware of the issue and being 100% sure I entered it in the day I pledged the money.

Were those by chance sent at a later date? That might explain why mine hasn't arrived yet.

to6ko91 · « **Reply #495 on:** November 19, 2013, 09:29:49 pm »

Another one in Ireland. 5 awesome µRulers just arrived to my doorstep today

EEVblog · « **Reply #496 on:** November 19, 2013, 10:24:38 pm »

Quote from: Stonent on November 19, 2013, 09:29:39 pm

Were those by chance sent at a later date? That might explain why mine hasn't arrived yet.

No, all were sent at the same time. I exported the database a day before they were sent, so if your address was in by then it would have made it, otherwise nothing was sent at all.

ddavidebor · « **Reply #497 on:** November 19, 2013, 10:38:11 pm »

No sign of uruler here in italy... :-(

iva · « **Reply #498 on:** November 19, 2013, 10:58:56 pm »

Received the rulers last weekend here in Southern Germany, the stamp says "Malmo, Sweden".

Made 3 friends happy and kept a couple for myself

Volta500 · « **Reply #499 on:** November 19, 2013, 11:27:14 pm »

Got my ruler today! Envelope in almost perfect condition with 5 rulers really well glued onto the cardboard, took some doing getting them off

Good job Dave!

Netherlands btw


EEVblog® Main Site	EEVblog® on Youtube	EEVblog® on Twitter	EEVblog® on Facebook	EEVblog® on Odysee

Author Topic: uRuler (Read 265707 times)

Share me