Author Topic: EEVblog #978 - Keysight 1000X Hacking  (Read 423231 times)

candrian and 12 Guests are viewing this topic.

Offline Mwyann

  • Contributor
  • Posts: 10
  • Country: fr
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #625 on: September 03, 2019, 05:27:23 pm »
New firmware available, v1.20 (1000XSeries.01.20.2019061038.ksx)

Release notes: https://www.keysight.com/upload/cmc_upload/All/Keysight_1000A_X_Series_Oscilloscope_Release_Notes_01_20.pdf

Looks like they don't made any effort to change over to linux.

If you revert back to the original firmware just use the original v1.10, until I update my code for the v1.20

Hi, any news regarding the 1.20 firmware hack?  ;)
 

Offline alpher

  • Frequent Contributor
  • **
  • Posts: 347
  • Country: ca
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #626 on: September 04, 2019, 04:50:50 pm »
Hi, could anyone that did the signal gen. in their EDUX1000G's post the correct part numbers needed, especially the package types (ie LM339 ? is it soic or tssop?) , it will be much appreciated.
Thank you.
 

Offline hv222

  • Regular Contributor
  • *
  • Posts: 66
  • Country: pl
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #627 on: September 05, 2019, 02:23:14 pm »
I don't know the exactly part numbers. I used 1% resistors, C0G/NP0 capacitors in signal patch and X7R, X5R (when X7R footprint was too big). Here are teardown photos https://www.flickr.com/photos/eevblog/33024469232/in/album-72157677358745114/

footprints:
U21, U43, U45 - 8 LD SOIC / SO-8
- LM4041CEM3-1.2/NOPB or any other with R1C marking -  SOT32
U22 - SO PowerPAD 8 (be aware, this part is also available on standard SO-8 without thermal pad)
U8, U10, U12 - SOIC-14
 

Offline alpher

  • Frequent Contributor
  • **
  • Posts: 347
  • Country: ca
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #628 on: September 05, 2019, 06:17:41 pm »
Thank you.
I just added these to my next order.
 ;)
 

Offline hv222

  • Regular Contributor
  • *
  • Posts: 66
  • Country: pl
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #629 on: September 05, 2019, 08:22:33 pm »
Don't forget about components in power supply patch. There are also unsoldered components - capacitors and linear regulators required for signal generator.
 

Offline alpher

  • Frequent Contributor
  • **
  • Posts: 347
  • Country: ca
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #630 on: September 05, 2019, 09:14:06 pm »
Damn  :( , capacitors I probably have but regulators probably not, can you share what kind?
Thanks again.
 

Offline hv222

  • Regular Contributor
  • *
  • Posts: 66
  • Country: pl
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #631 on: September 05, 2019, 10:11:46 pm »
Just standard 78xx and 79xx family. All you need you have on teardown photos, except MLCC values. For 0603 footprint I used 100nF, for bigger one something between 1 and 10uF. I don't remember.
 

Offline tudou2048

  • Newbie
  • Posts: 5
  • Country: cn
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #632 on: September 06, 2019, 11:22:49 am »
Maybe 78L05 and 79L05.
 

Offline alpher

  • Frequent Contributor
  • **
  • Posts: 347
  • Country: ca
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #633 on: September 06, 2019, 01:11:49 pm »
Sounds reasonable, will have to buy some of them.
Thanks guys.
 

Offline bd139

  • Super Contributor
  • ***
  • Posts: 23018
  • Country: gb
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #634 on: September 08, 2019, 11:58:07 am »
I was going to dump my DS1054Z and buy an MSO5000 but the thing misses the mark on a lot of points so I'm not going in that direction again.

Thus I'm looking at grabbing a DSOX1204G. Does anyone know if there is a crack for the D1200BW2A bandwidth option and the D1200EMBA decode options? I don't need either of them immediately as such so this is an exploratory question.
 
The following users thanked this post: Free_WiFi, analogRF

Online tv84

  • Super Contributor
  • ***
  • Posts: 3212
  • Country: pt
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #635 on: October 05, 2019, 09:57:16 pm »
Today I had a peek at FERCSA's work.  :clap: Interesting!  ::)

Maybe I can add something to it, although I've never seen a 1000X.

 
The following users thanked this post: skander36

Online Fungus

  • Super Contributor
  • ***
  • Posts: 16562
  • Country: 00
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #636 on: October 10, 2019, 07:47:57 am »
Today I had a peek at FERCSA's work.  :clap: Interesting!  ::)

Where can we see it...?

 

Online Fungus

  • Super Contributor
  • ***
  • Posts: 16562
  • Country: 00
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #637 on: October 10, 2019, 07:49:56 am »
Thus I'm looking at grabbing a DSOX1204G. Does anyone know if there is a crack for the D1200BW2A bandwidth option and the D1200EMBA decode options? I don't need either of them immediately as such so this is an exploratory question.

Yes, there is.
 

Online 2N3055

  • Super Contributor
  • ***
  • Posts: 6453
  • Country: hr
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #638 on: October 10, 2019, 08:01:43 am »
Thus I'm looking at grabbing a DSOX1204G. Does anyone know if there is a crack for the D1200BW2A bandwidth option and the D1200EMBA decode options? I don't need either of them immediately as such so this is an exploratory question.

Yes, there is.

For 4ch Linux based DSOX1204G ? where?
 

Online Fungus

  • Super Contributor
  • ***
  • Posts: 16562
  • Country: 00
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #639 on: October 10, 2019, 09:10:19 am »
Yes, there is.

For 4ch Linux based DSOX1204G ? where?

Oh, the DSOX1204G   :palm:  :-[ :-[ :-[ :-[

I'm not sure, but look for DSOX2000 and DSOX3000 hacks. I believe the hacks are the same across families.


« Last Edit: October 10, 2019, 09:53:51 am by Fungus »
 

Offline Cesarsound

  • Newbie
  • Posts: 9
  • Country: br
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #640 on: December 15, 2019, 02:26:49 am »
DSOX1102G HKD Decoding I2C data bus from Si4735:

https://youtu.be/lSvhhtFS3_Y
« Last Edit: December 15, 2019, 02:40:10 am by Cesarsound »
 

Offline TK

  • Super Contributor
  • ***
  • Posts: 1722
  • Country: us
  • I am a Systems Analyst who plays with Electronics
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #641 on: December 15, 2019, 03:50:54 am »
Yes, there is.

For 4ch Linux based DSOX1204G ? where?

Oh, the DSOX1204G   :palm:  :-[ :-[ :-[ :-[

I'm not sure, but look for DSOX2000 and DSOX3000 hacks. I believe the hacks are the same across families.
The DSOX1204G is Linux based, not Windows CE like the 2000X or 3000X.  There is no known hack yet
 
The following users thanked this post: stafil

Offline skander36

  • Frequent Contributor
  • **
  • Posts: 704
  • Country: ro
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #642 on: December 15, 2019, 07:26:53 am »
The DSOX1204G is Linux based, ...
[/quote]
Are you sure ? How do you know ? There is some info available ?
 

Offline skander36

  • Frequent Contributor
  • **
  • Posts: 704
  • Country: ro
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #643 on: December 15, 2019, 08:28:48 am »
 

Offline BubbaMc

  • Contributor
  • Posts: 12
  • Country: au
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #644 on: January 22, 2020, 11:42:17 pm »
Hi all, apologies if this has been covered, but is it possible to hack the EDUX1002A to EDUX1002G or DSOX1002G?

I think it's possible, but just wanted to make sure before I place an order.

Thank you!
 

Offline Mwyann

  • Contributor
  • Posts: 10
  • Country: fr
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #645 on: February 26, 2020, 04:48:17 pm »
Today I had a peek at FERCSA's work.  :clap: Interesting!  ::)

Maybe I can add something to it, although I've never seen a 1000X.

Any news about that work?  ;D
 

Offline jusaca

  • Supporter
  • ****
  • Posts: 69
  • Country: de
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #646 on: February 27, 2020, 07:37:18 am »
At the embedded world yesterday I was told that in a couple of days there will be a new firmware for the Non-EDU versions to increase waveform update rate to 200.000 /s and to always enable serial decode/trigger!
Now I'm waiting quite excited to finally play with the serial options on my 1000x ;)

 

Offline TK

  • Super Contributor
  • ***
  • Posts: 1722
  • Country: us
  • I am a Systems Analyst who plays with Electronics
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #647 on: February 27, 2020, 11:51:22 am »
EDU models can be converted to DSO by changing 2 resistors... does it mean you can have free serial decoding and 200,000wfm/s on EDU models?  Interesting  :popcorn:
 

Offline alpher

  • Frequent Contributor
  • **
  • Posts: 347
  • Country: ca
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #648 on: February 27, 2020, 06:10:03 pm »
I don't think that it's that simple. Frontend needs substantial rework and sign gen section is  missing  quite a few components. Don't forget about the trigger too.
 

Offline TK

  • Super Contributor
  • ***
  • Posts: 1722
  • Country: us
  • I am a Systems Analyst who plays with Electronics
Re: EEVblog #978 - Keysight 1000X Hacking
« Reply #649 on: February 27, 2020, 06:14:55 pm »
I know about the frontend limitation and signal generation section missing (only on A models).  I am just talking about 200,000 wfm/s update rate and serial decoding.
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf