So i got an Samsung device instead of the Symetricon.
Not so much difference i gues, both have a OCXO and both have a GPS.
I figured out the Serial port, baudrate and gave some commands and status update with Putty.
It is recognized by Lady Heather, but she shows no data on the screen, but the data is flowing (sniffer).
Maybe not supported yet i gues..
Already figured out that the command do not are retentive, so after every powercycle you need to do some settings.
Like in my case where the standard settings are not usable.
- UCCM Slot STATE -
1-1 #Now UCCM STATUS ----------------------------[Alarm]
1-2 #Before UCCM STATUS -------------------------[OCXO Warm]
2-1 #Reference Clock Operation ------------------[Not Used]
2-2 #Current Reference Type ---------------------[Ext Clock]
2-3 #Current Select Reference -------------------[NOT SELECT][Ext
?]
2-4 #Current Reference Status -------------------[Unavailable]
#GPS STATUS ---------------------------------[Unavailable]
#Priority Level -----------------------------[EXT->GPS]
#ALARM STATUS
#H/W FAIL -----------------------------------[NONE]
#OPERATION ALARM ----------------------------[EXTREF]
PLL STATUS ----------------------------------[Disable]
Current PLL MODE ----------------------------[OFFSET OBSERVATION MODE]
"Command Complete"
So i know now i need the commands:
sync:ref:disable ext
sync:ref:enable GPS
Ref:Type GPS
I can have a arduino do that for me, maybe even a display handler to get the status on a display.
Stat after these commands:
1-1 #Now UCCM STATUS ----------------------------[Alarm]
1-2 #Before UCCM STATUS -------------------------[OCXO Warm]
2-1 #Reference Clock Operation ------------------[Not Used]
2-2 #Current Reference Type ---------------------[Ext Clock]
2-3 #Current Select Reference -------------------[GPS 1PPS]
2-4 #Current Reference Status -------------------[Available]
#GPS STATUS ---------------------------------[Available]
#Priority Level -----------------------------[EXT->GPS]
#ALARM STATUS
#H/W FAIL -----------------------------------[NONE]
#OPERATION ALARM ----------------------------[Antenna]
PLL STATUS ----------------------------------[Enable]
Current PLL MODE ----------------------------[FAST LOCKING MODE]
Still have to figure out what the ANTENNA OPER alarm is about.
GPS is locking etc so no big deal i gues.
for the rest everything looks good:
UCCM> syst:stat?
-------------------------------------------------------------------------------
UCCM-L8 serial number SE2D307230 firmware ver 1.0.0.3-02 GPS(or Ext) mode
-------------------------------------------------------------------------------
Reference Status __________________________ Reference Outputs _______________
XXExt Ref : Unknown[LOS]
TFOM 2 FFOM 1
UCCM A Status[Master]
>>GPS : [phase : -6.500E-8]
ACQUISITION ................................................ [ GPS 1PPS Valid ]
Tracking: 5 ___ Not Tracking: 6 _______ Time ____________________________
PRN El AZ CNO PRN El Az GPS 23:01:40 19 NOV 2019
2 31 53 43 6 4 24 GPS Synchronized to UTC
12 23 94 44 14 26 254 ANT DLY +0.0E+0
25 69 91 49 21 4 182 Position ________________________
29 74 199 50 23 1 347 MODE fixed
31 55 287 48 26 17 282
32 12 228 FIX LAT N 52:xx:xx.xxx
FIX LON E 4:xx:xxx.xxx
FIX HGT +43.97 m
ELEV MASK 5 deg ANT V=5.148V, I=16.160mA
-------------------------------------------------------------------------------
Temp = 34.000 / Antenna
"Command Complete"
Anything else to do or to take care of?
all hints would be appreciated..