Author Topic: SR620 TI setup procedure?  (Read 3411 times)

0 Members and 1 Guest are viewing this topic.

Offline notfaded1Topic starter

  • Frequent Contributor
  • **
  • Posts: 559
  • Country: us
SR620 TI setup procedure?
« on: April 05, 2020, 06:57:09 pm »
Minus the data in the manual I've seen a few extra docs floating around but am not sure where to find them now?  Setup procedures for the SR620 for getting best time interval readings.  How do you configure yours?  In frequency I know the SR620 may actually be worse than HP53132A but for time interval it's one of the kings.  This is my Thunderbolt 10MHz feeding into SR620 on Frequency.

I've wanted one of these for while and finally got a nice one with option 1.

Bill
« Last Edit: April 05, 2020, 06:59:27 pm by notfaded1 »
.ılılı..ılılı.
notfaded1
 

Offline notfaded1Topic starter

  • Frequent Contributor
  • **
  • Posts: 559
  • Country: us
Re: SR620 TI setup procedure?
« Reply #1 on: April 05, 2020, 07:32:59 pm »
That was cold I'm trying it again after warming up for a while... I found this guide from NASA.  I need to feed it external reference next.
« Last Edit: April 05, 2020, 07:59:55 pm by notfaded1 »
.ılılı..ılılı.
notfaded1
 

Offline notfaded1Topic starter

  • Frequent Contributor
  • **
  • Posts: 559
  • Country: us
Re: SR620 TI setup procedure?
« Reply #2 on: April 05, 2020, 07:49:55 pm »
Looks much better after warming up some.
.ılılı..ılılı.
notfaded1
 

Offline Theboel

  • Frequent Contributor
  • **
  • Posts: 278
  • Country: id
Re: SR620 TI setup procedure?
« Reply #3 on: April 05, 2020, 08:54:03 pm »
Hi notfaded1,

look at PRS10 manual
https://www.thinksrs.com/downloads/pdfs/manuals/PRS10m.pdf
You can find how to set SR620 for "coarse and fine" measurement

Anton
 
The following users thanked this post: notfaded1

Offline notfaded1Topic starter

  • Frequent Contributor
  • **
  • Posts: 559
  • Country: us
Re: SR620 TI setup procedure?
« Reply #4 on: April 05, 2020, 09:07:34 pm »
look at PRS10 manual
https://www.thinksrs.com/downloads/pdfs/manuals/PRS10m.pdf
You can find how to set SR620 for "coarse and fine" measurement
Thanks this reminded me where I saw some of this before!  I'm waiting for a new 24V 3A power supply that should come tomorrow for a recently acquired a PRS10.  I have a Ublox LEA-6T on a pcb that can discipline the PRS10 that I was hoping might become my new house standard.  Thanks for the tip!

Bill
.ılılı..ılılı.
notfaded1
 

Offline Theboel

  • Frequent Contributor
  • **
  • Posts: 278
  • Country: id
Re: SR620 TI setup procedure?
« Reply #5 on: April 06, 2020, 01:27:01 am »
Thanks this reminded me where I saw some of this before!  I'm waiting for a new 24V 3A power supply that should come tomorrow for a recently acquired a PRS10.  I have a Ublox LEA-6T on a pcb that can discipline the PRS10 that I was hoping might become my new house standard.  Thanks for the tip!


Hi Bill,

I love to hear about PRS10 discipline with ublox 6T and TDEV and MDEV chart will great.
May I Suggest You to use a the best cable for made measurement. same length same type same connector brand and made at least 3 time measurement and the last one stay away from off line UPS  :phew: :phew: :phew:

Anton
 
The following users thanked this post: notfaded1


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf