Electronics > Open Source Hardware

LibreTimeBase: A Controller & Distribution Amplifier for Rubidium Frequency Stds

(1/1)

wergor:
I'd like to introduce my Project:
LibreTimeBase - an OSHW Controller and Distribution Amplifier for Rubidium Frequency Standards (and OCXOs).

This Project is my first step into timenuttery and "RF" stuff. The goal is to create a device that can interface with a wide range of Rubidium Frequency Standards and provide additional functionality:

* Distribution Amplifier with isolated outputs
* Clock Generation and 5V TTL clock output
* Calibration and adjustments via Electronic Frequency Control or Serial Interface
* 1PPS in as a calibration reference or master clock for the Rubidium Frequency Standard
* 1PPS output with user selectable pulse length (and frequency, need not be 1PPS)
* Monitoring of operating parameters and health indicators (Built In Test Equipment, Supply Current, Temperature, Lamp Voltages, ...)
* Supply Voltage monitoring, overvoltage and reverse voltage protection
The device (WIP!) here shown with an Accubeat AR-133:

PDF Schematic (also WIP!): https://bitbucket.org/christandlg/libretimebase/src/dev/pcb/LibreTimeBase/schematic.pdf

Rubidium Frequency Standards will be mounted onto or over the board (depending on size) and will interface to the device via a riser card. The riser card will contain components specific to the Standard (attenuators, voltage dividers, ...) and bulk capacitors. I'm trying to use the center of the board, which will be covered by a RFS anyway, as a space to put the riser cards so that users can just break away and populate the riser card they need. Riser cards use Samtec MEC8 edge connectors, the pinout is chosen to prevent damage in case of reverse insertion.
The Standard's reference output will be filtered by a 5th order elliptic filter before being buffered by a pair of LT6550 triple video amps. 5 of the 6 video amp outputs are isolated with TC1-1T transformers and feed the device's 5 Reference Frequency outputs. Video amp output 6 feeds a LTC6957 clock generator which in turn feeds a 74HCT driver for the 5V TTL clock output. An AD5689R 16-bit DAC is used for EFC, a MAX3232 supports RS-232 communication with supporting Standards. An AD8213 measures the Standard's supply current.
Finally, a STM32F072 controls and monitors everything. The STM32's clock is also driven by the LTC6957 and feeds the 74HCT driver for the 5V 1PPS output signal.
The Supply Voltage is filtered and reverse polarity protected. No DC-DC converter is present, so the Standard is driven directly off the Supply Voltage. The STM32 monitors both Supply Voltage and Current and can switch off the Standard's Supply in fault conditions. The device can operate from 9V to 32V (Abs. Max. 36V), depending on the Standard's requirements.

After an extensive market research I have identified the following Rubidium Frequency Standards as candidates for support:

* FEI FE-5680
* Efratom / Datum / ... LPRO-101
* Accubeat AR-40A, AR-60A, AR-133
* Stanford Research PRS-10OCXOs will also be supported, like the Trimble 65256.
These Standards have different characteristics (mechanical dimensions, supply requirements, output power, analog / digital interfaces, ...) which define the requirements for the device, e.g. the wide Supply Voltage Range.

The device is designed to be used either as a module for the Envox EEZ BB3 or as a standalone device. When used as a BB3 module, functionality will be exposed via the BB3 User Interface and SCPI via the BB3's remote interfaces. Unfortunately, with most types of Rubidium Frequency Standard installed the device will take up more than 1 slot of the BB3.
When used as a standalone device a SCPI interface will be exposed via USB. The PCB is 100mm wide, so the device can be housed in common extruded aluminum cases for 100mm PCBs.

Navigation

[0] Message Index

There was an error while thanking
Thanking...
Go to full version