Poll

Which form factor do you want to see

Gum stick with dual USB-C ports
11 (47.8%)
Module with LGA land patterns
2 (8.7%)
Module with micro mezzanine connectors
10 (43.5%)

Total Members Voted: 23

Author Topic: [Poll] FPGA board form factor  (Read 5928 times)

0 Members and 1 Guest are viewing this topic.

Offline ebclr

  • Super Contributor
  • ***
  • Posts: 2199
  • Country: 00
Re: [Poll] FPGA board form factor
« Reply #75 on: September 28, 2020, 09:11:20 am »
Sugestion , Put a 1 Led or 2 , To and deliver with the LedBlink VHDL loaded, This can be helpful to starters
 

Offline ali_asadzadeh

  • Super Contributor
  • ***
  • Posts: 1253
  • Country: ca
Re: [Poll] FPGA board form factor
« Reply #76 on: September 28, 2020, 11:03:54 am »
Any progress regarding JTAG bit-bang with the MCU?
I'm a Digital Expert from 8-bits to 64-bits
 

Online blueskull

  • Supporter
  • ****
  • Posts: 14182
  • Country: cn
  • Power Electronics Guy
Re: [Poll] FPGA board form factor
« Reply #77 on: September 28, 2020, 12:56:20 pm »
Any progress regarding JTAG bit-bang with the MCU?

Yes. I'm working on a commercial gw1nr board and I'm boot loading it with ch552. It is still wip and I'll open source as much as I can.
 
The following users thanked this post: ali_asadzadeh

Offline ali_asadzadeh

  • Super Contributor
  • ***
  • Posts: 1253
  • Country: ca
Re: [Poll] FPGA board form factor
« Reply #78 on: September 29, 2020, 06:25:26 am »
Thanks, that's great, Also I'm working with Gowin now, my main problem is the lack of simulation models for IP cores, How do you debug your code? have you found any work around the simulation?
It really has stucked me |O
I'm a Digital Expert from 8-bits to 64-bits
 

Online blueskull

  • Supporter
  • ****
  • Posts: 14182
  • Country: cn
  • Power Electronics Guy
Re: [Poll] FPGA board form factor
« Reply #79 on: September 29, 2020, 11:15:39 am »
Thanks, that's great, Also I'm working with Gowin now, my main problem is the lack of simulation models for IP cores, How do you debug your code? have you found any work around the simulation?
It really has stucked me |O

I don't simulate. I pull critical nets to pins and probe them.
 
The following users thanked this post: ali_asadzadeh

Online blueskull

  • Supporter
  • ****
  • Posts: 14182
  • Country: cn
  • Power Electronics Guy
Re: [Poll] FPGA board form factor
« Reply #80 on: October 17, 2020, 02:47:13 pm »
While I'm still working on the CH552 port of it, I figure I can just upload the official JTAG program I obtained from the FAE for loading into SRAM.

Loading into external flash is possible, but I don't have the program.
 

Offline ali_asadzadeh

  • Super Contributor
  • ***
  • Posts: 1253
  • Country: ca
Re: [Poll] FPGA board form factor
« Reply #81 on: October 20, 2020, 11:46:32 am »
Thanks for sharing ;)
I'm a Digital Expert from 8-bits to 64-bits
 

Online blueskull

  • Supporter
  • ****
  • Posts: 14182
  • Country: cn
  • Power Electronics Guy
Re: [Poll] FPGA board form factor
« Reply #82 on: October 23, 2020, 06:54:48 am »
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf