Electronics > Projects, Designs, and Technical Stuff

DIY cheap powerbank (technical suggestions R welcome !)

<< < (11/13) > >>

crazyguy:

--- Quote from: ym58 on August 11, 2016, 04:51:52 am ---
--- Quote from: crazyguy on August 11, 2016, 03:50:57 am ---use a large heat sink will increase the size of the powerbank

--- End quote ---

Well it's not so large, the width is only 14mm (0.55 inch) and the height 6mm (0.23 inch) !
And I was thinking I could trim its length according to the hot surfaces it has to be glued on on each side of the PCB ...






--- Quote from: crazyguy on August 11, 2016, 03:50:57 am ---I don't think you can purchase this demo board anywhere, send a email to the IC company maybe they would be kind enough to give you a copy for testing
--- End quote ---

That's what I'll do.
Is Changdiantou a distributor only or the original IC company ?
Apparently, their website is about video rentals ... ?!?



--- End quote ---

chongdiantou is a forum interested in charger, they are not distributor

the IC company name is INJOINIC Technology
http://www.injoinic.com/
their website says
For English Datasheets, please mail to SERVICE@INJOINIC.COM

crazyguy:

--- Quote from: blueskull on August 11, 2016, 06:14:49 am ---BTW, there is a BQ24295 that does the same thing, it can only boost to 1.5A, but it can charge at 3A. It is one of the rare USB OTG ICs that have a separate boost output other than charging input.

--- End quote ---

BQ24195 can boost to 5.1V@2.1A

I2C Controlled 2.5A/4.5A Single Cell Charger with 5.1V 1.3A/2.1A Synchronous Boost Operation
http://www.ti.com/product/bq24195

ym58:

--- Quote from: blueskull on August 11, 2016, 06:14:49 am ---BTW, there is a BQ24295 that does the same thing, it can only boost to 1.5A, but it can charge at 3A. It is one of the rare USB OTG ICs that have a separate boost output other than charging input.

--- End quote ---

--- Quote from: crazyguy on August 11, 2016, 07:11:59 am ---BQ24195 can boost to 5.1V@2.1A
I2C Controlled 2.5A/4.5A Single Cell Charger with 5.1V 1.3A/2.1A Synchronous Boost Operation
http://www.ti.com/product/bq24195

--- End quote ---
Those ones (BQ24195 and BQ24295) are killers and do everything I want (Boost 5V/1.5A or 2.1A and up to 4.5A CC charger) but honestly it does not worth designing a new PCB just for the beauty of gesture ;)
In addition, I have no knowledge in I2C management designing ...
I would be better off with a ready made solution like the IP5109 stuff ....

ym58:

--- Quote from: crazyguy on August 11, 2016, 06:55:08 am ---chongdiantou is a forum interested in charger, they are not distributor
the IC company name is INJOINIC Technology
http://www.injoinic.com/
their website says
For English Datasheets, please mail to SERVICE@INJOINIC.COM
--- End quote ---
Thanks, I've just contacted them ... will let you all know about the status here.

ym58:

--- Quote from: crazyguy on August 11, 2016, 06:55:08 am ---the IC company name is INJOINIC Technology
their website says
For English Datasheets, please mail to SERVICE@INJOINIC.COM
--- End quote ---

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod