Author Topic: Proteus Design Suite Automatically closes uncertainly.  (Read 14221 times)

0 Members and 1 Guest are viewing this topic.

Offline SiddhatTopic starter

  • Regular Contributor
  • *
  • Posts: 52
  • Country: np
Proteus Design Suite Automatically closes uncertainly.
« on: September 22, 2019, 04:55:34 pm »
Hey guys, I just installed Proteus Design Suite v8.9 on my computer. But the problem is that the software automatically closes when a simulation is running, or when a schematic is being made. Even during a simple circuit simulation of a Battery, resistor and a LED, the software closes. I've had this problem in Proteus v8.7, v8.8 and now v8.9. I updated to 8.9 hoping the problem would solve but it is still the same. I've lost so many important schematics till now, even when designing it's not just convenient. Anyone facing the same problems? And any ideas how to solve the problems? Appreciate your help.
 

Online Simon

  • Global Moderator
  • *****
  • Posts: 17729
  • Country: gb
  • Did that just blow up? No? might work after all !!
    • Simon's Electronics
Re: Proteus Design Suite Automatically closes uncertainly.
« Reply #1 on: September 22, 2019, 06:22:24 pm »
Contact their support. They are generally quite good and unlike other vendors will genuinely investigate.
 

Offline HarryMan

  • Newbie
  • Posts: 4
  • Country: ua
Re: Proteus Design Suite Automatically closes uncertainly.
« Reply #2 on: January 13, 2020, 09:04:07 am »
Did you solve the problem? I also have such a problem.
Do you use the official version? or hacked?
 

Online Psi

  • Super Contributor
  • ***
  • Posts: 9889
  • Country: nz
Re: Proteus Design Suite Automatically closes uncertainly.
« Reply #3 on: January 13, 2020, 09:18:20 am »
Could be an issue with bad RAM, or bad VRAM if using some sort of GFX compute acceleration.
An error like that could create a situation where the app just terminates.

Run a RAM and VRAM test for a while and see if you find any errors.
« Last Edit: January 13, 2020, 09:20:12 am by Psi »
Greek letter 'Psi' (not Pounds per Square Inch)
 

Offline ebclr

  • Super Contributor
  • ***
  • Posts: 2328
  • Country: 00
Re: Proteus Design Suite Automatically closes uncertainly.
« Reply #4 on: January 14, 2020, 12:42:00 am »
I had the same problem for years,  never solved, and moved away from this toy software
 

Online Simon

  • Global Moderator
  • *****
  • Posts: 17729
  • Country: gb
  • Did that just blow up? No? might work after all !!
    • Simon's Electronics
Re: Proteus Design Suite Automatically closes uncertainly.
« Reply #5 on: January 14, 2020, 07:37:28 am »
did you actually speak to them?
 

Offline alex-kv

  • Newbie
  • Posts: 2
  • Country: fr
Re: Proteus Design Suite Automatically closes uncertainly.
« Reply #6 on: April 07, 2022, 06:40:59 am »
I had this issue and I have found a workaround  that works for me. To me proteus may automatically close during or after I launched the simulation, but never happened again since I no longer use animated measuring devices like voltmeter, ammeter.
To measure a voltage I use the "probe mode" measuring device. The device under "laplace primitive" named "OP : substract" can be used to measure a resistor voltage and the a voltage probe have to be placed at the output of the substract op.
To measure a current I use the same technique with a shunt resistor.

Hope that could help..
« Last Edit: April 07, 2022, 07:48:57 am by alex-kv »
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf