Electronics > Repair
Aeroflex IFR-2398 / calibration / repair help
<< < (13/16) > >>
doarmin:
Bonsoir merci beaucoup celà m'aide énormément...J'avais bien vu que ces condensateurs étaient en parallèle mais cette platine a au moins trois couches
et pas simple de suivre...J'ai un peu moins de 6 ohms  aux bornes de ces condensateurs et de nombreuses résistances de 15 ohms  R01 à R08 se sont coupées face à ce presque court circuit une seule semble avoir tenu le coup ...celà explique la présence encore du +15V venant du connecteur de l'alimentation principale.
Résultat : pas de vidéo et échec au niveau du level lors de l'autotest.par contre la Fi 10,7mhz rentre bien sur cette platine  visiblement l'option peack n'est pas concernée par ce + 15V en presque court circuit mais d'autres circuits sur la platine doivent etre concernés mais j'ai pas de détails....ou alors un des condensateurs C173 à C177 défectueux...J'aimerais bien car travail de fourmis autrement.
Bests regarts.
George Edmonds:
Looking at the information that I have it appears that the +15VDC supply to virtually every IC on the board is decoupled with a 22uf 20V working capacitor with either a 0.1uf or a 0.01uf capacitor in parallel, some IC’s look like they us the +15VDC twice with separate decoupling capacitors.

Regrettably there is no power distribution schematic or a parts list in the information that I have.  May I suggest that you measure the resistance of the +15VDC supply to ground either side of the two 22 Ohms resistors in parallel, this may give you a clue as to if the fault is the filter or is one of the IC supply decoupling capacitors.

All the best and hope that you succeed, if I can help more just ask.

George Edmonds
doarmin:
Bonsoir.
Faisant suite à vos conseils j'ailevé une à une les condensateurs du filtre puis les découplages du +15V je retrouve encore 2?5ohms par rapport à la masse.
Plus de doute il reste trois CI reliés à cette ligne +15V
U5  U16 et U13 .Plus rien de connecté sur cette platine.A part U5 bien connu un CA2111A les autres ne me disent rien...j'ai besoin d'aide avant de les retirer l'un après l'autre...
George Edmonds:
Hi

Before I continue may I say that I only have a very limited understanding of technical French and am basically using Google Translator, so certain points are probably being lost in translation.  I also do not have an IFR2398 at present so I am working from an incomplete set of factory schematics.  I do have the IFR service manual, but it is a module replace only manual as all boards/modules were intended to be returned to the factory in South Korea for low level repairs to be carried out

In your last email you said “U5, U16, and U13 Nothing else connected on this plate”.  I suspect that plate should be PCB, from what information that I have there are some 38 IC’s on the PCB with well over 50% using the +15VDC supply, this supply is also used for multiple other purposes and is heavily decoupled with electrolytic capacitor using 0.1uf capacitors in parallel and sometimes just the 0.1uf capacitors.

I do not believe that removing capacitors/IC’s one after another is a valid method of finding the fault as you are very likely to cause damage to the PCB by doing so, my suspicion is that the PCB is at least a four layer one.

In the past I have asked you to check to ground the resistance at either end of the R223 in parallel with R223A.  These resistance measurements should be made using a four wire Kelvin setup.

How you find the short on the PCB depends on the equipment available to you, you need to be able to put a constant current into the PCB +15VDC supply rail and then trace the test current to the fault, there are many ways of doing this, but they all involve specialist equipment that you may not have.  I have an HP set of probes that can inject a pulsed current and then follow the pulsed current about the PCB to the shorted device.

I have scanned the 511-648-A board block diagram and have attached it to this posting.

George Edmonds
doarmin:
bonsoir merci pour votre réponse.Je vois que vous etes très équipé en matière de recherche de panne...Il y a certes beaucoup de circuits intégrés sur la carte mais après avoir cherché les connections au +15v il y en a seulement 3 qui le sont directement les autres sont à un 5V distribué autrement ou alors il y a une régulation permettant peut etre de fabriquer un +9 10 12 ou autre mais n'ayant pas le schemas...
S'est effectivement une carte avec plusieurs couches et le +15V est distribué ainsi sur toute la carte...En connection directe il y a les trois ci que j'ai identifié après un vrai jeu de pistes:
 Un CA2111A. un MC1350.  et un CA3089.
Oui s'est trés risqué sur un multicouches de sortir un ci traversant comme le CA2111A.En fait la nuit dernière j'ai eu une idée : comme la résistance entre le OV et le +15V est de 2,5ohms j'ai alimenté la carte avec 2V puis utilisé une camera Thermique ce qui m'a permis de voir C154 chauffer puisque parcoutu par un courant de 800mA...méthode certes un peu hors normes mais le résultat est là.Ce condensateur pourtant vérifié etait passé hors vigilance ayant du vernis sur les soudures...L'IFR2398 est reparti comme avant.merci pour votre aide dans cette aventure car j'aurais eu du mal à trouver sans vos conseils.
Navigation
Message Index
Next page
Previous page
There was an error while thanking
Thanking...

Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod