Electronics > Repair
Flux, "No Clean" Flux, Cleaning, and Re-Coating?
<< < (3/3)
Fried Chicken:

--- Quote from: David Hess on January 16, 2025, 01:59:04 am ---Isopropyl alcohol has the virtue of being inexpensive, readily available, and safe, but by itself it is not a very good flux cleaner.  A mixture of 50/50 isopropyl alcohol and toluene is much better, and a great flux thinner, but toluene is no longer readily available.


--- Quote from: Fried Chicken on January 16, 2025, 12:46:12 am ---I'm kind of a fan of 63/37 solder, why isn't it more common?  Or should I just get 60/40?
--- End quote ---

Sn60Pb40 is slightly less expensive than Sn63Pb37.  Otherwise they are practically identical.

--- End quote ---

Are there any fluxes that clean well with IPA?
I'm genuinely allergic to nasty solvents as I do my work basically in the house.
aeberbach:
If the flux is hard, such as produced by rosin-core solder, use a soft tool like a bamboo skewer to chip off the big lumps of flux first and then brush/vacuum the board before using the IPA. It will take about half the time to fully clean.
David Hess:

--- Quote from: Fried Chicken on January 16, 2025, 05:06:13 am ---
--- Quote from: David Hess on January 16, 2025, 01:59:04 am ---Isopropyl alcohol has the virtue of being inexpensive, readily available, and safe, but by itself it is not a very good flux cleaner.  A mixture of 50/50 isopropyl alcohol and toluene is much better, and a great flux thinner, but toluene is no longer readily available.
--- End quote ---

Are there any fluxes that clean well with IPA?
I'm genuinely allergic to nasty solvents as I do my work basically in the house.
--- End quote ---

The water soluble fluxes might clean well with only IPA, but you should not be using them anyway.

I never had good results using only IPA with any flux.  I have tended to use acetone, which other than being flammable is one of the least toxic options.  I would test and use MEK and toluene if I could get them more easily.  Degreasers like 1,1,1-Trichloroethane are excellent at removing flux.  Maybe spray brake or carburetor cleaner would be a good option?

You could examine the MSDSes for various spray flux removers to get some ideas.  They usually work very well.
Fried Chicken:

--- Quote from: David Hess on January 16, 2025, 04:21:27 pm ---
--- Quote from: Fried Chicken on January 16, 2025, 05:06:13 am ---
--- Quote from: David Hess on January 16, 2025, 01:59:04 am ---Isopropyl alcohol has the virtue of being inexpensive, readily available, and safe, but by itself it is not a very good flux cleaner.  A mixture of 50/50 isopropyl alcohol and toluene is much better, and a great flux thinner, but toluene is no longer readily available.
--- End quote ---

Are there any fluxes that clean well with IPA?
I'm genuinely allergic to nasty solvents as I do my work basically in the house.
--- End quote ---

The water soluble fluxes might clean well with only IPA, but you should not be using them anyway.

I never had good results using only IPA with any flux.  I have tended to use acetone, which other than being flammable is one of the least toxic options.  I would test and use MEK and toluene if I could get them more easily.  Degreasers like 1,1,1-Trichloroethane are excellent at removing flux.  Maybe spray brake or carburetor cleaner would be a good option?

You could examine the MSDSes for various spray flux removers to get some ideas.  They usually work very well.

--- End quote ---

I. Am. Losing. My. Mind. Here.

Acetone is likely the move.  I'll skip the water cleanup fluxes.  Now I just need to decide on which flux to purchase.  I got a flux pen, so I guess I need a less viscous flux for that, and I still have my existing MG flux that seems pretty corrosive if not cleaned.

Recommendations are:
SMD291NL for its low viscosity and re-usability, TACFLUX-020 ($23 from Tequipment for 10cc) or TACFLUX-020B ($28 from Tequipment for 30cc) as it "passes SIR test in a unreflowed state" or "passes SIR test once ...".  I found this on tequipment, but it had a low recommended use temperature.
A recommendation for exclusively SMT/SMD flux b/c it's somehow better.

And for solder: Skip the ROHS compliant; but now there's a million options for solder, 60/40, 63/37, lead-free, various flux core types, and diameters.
Writing all this down as notes for myself.

I. Am. Losing. My. Mind. Here.
Navigation
Message Index
Previous page
There was an error while thanking
Thanking...

Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod