Author Topic: Identifying a fuse  (Read 1248 times)

0 Members and 1 Guest are viewing this topic.

Offline deisenbergTopic starter

  • Contributor
  • Posts: 40
  • Country: ca
  • Seriously I have no clue.
Identifying a fuse
« on: January 27, 2020, 09:54:56 pm »
I have a PSU from a Sony dvp-cx985v disc changer that I some how popped an on board fuse, two actually. At least I believe they are fuses. Both look the same, see picture. I can't figure out how to identify it for the life of me. It's the green with 1 black strip, item pcb number p502

Part number in the schematics is 9-885-024-65 labelled as a link IC - no idea why as it's for the -11v rail.

Thanks everyone!

Edit: added model of sony disc changer
« Last Edit: January 28, 2020, 02:29:40 pm by deisenberg »
 

Offline fzabkar

  • Super Contributor
  • ***
  • Posts: 2735
  • Country: au
Re: Identifying a fuse
« Reply #1 on: January 28, 2020, 12:32:16 am »
Picofuse?
 

Offline notsob

  • Frequent Contributor
  • **
  • Posts: 706
  • Country: au
Re: Identifying a fuse
« Reply #2 on: January 28, 2020, 02:39:50 am »
looks like a zero ohm resistor
 

Offline Nusa

  • Super Contributor
  • ***
  • Posts: 2418
  • Country: us
Re: Identifying a fuse
« Reply #3 on: January 28, 2020, 03:52:35 am »
I'd agree if the black stripe were in the middle, which it is not. Fuses are essentially zero-ohm resistors until they become open-circuit resistors.

P is an unusual prefix for a fuse, however. Looks like there's something on the PCB under the fuse. Perhaps a better look at that might be helpful?
 

Offline floobydust

  • Super Contributor
  • ***
  • Posts: 7593
  • Country: ca
Re: Identifying a fuse
« Reply #4 on: January 28, 2020, 04:07:38 am »
It would be a Japanese-make part and hard to know who makes it. In North America Littelfuse is the only thing close, and best to use a slo-blo part as many Picofuses are super fast and not ideal where inrush currents happen.
It should have colour-coding beyond one stripe so you know what the fuse's value is and don't mix them up in Production. If the other fuses are different value but same markings then I would be puzzled or tend to think it's zero-ohm jumper.
 
The following users thanked this post: deisenberg

Offline goaty

  • Regular Contributor
  • *
  • Posts: 206
  • Country: de
Re: Identifying a fuse
« Reply #5 on: January 28, 2020, 12:58:40 pm »
9-885-024-65
is described as
"Ic Protector 20N1000"
https://encompass.com/item/6425943/Sony/9-885-024-65/

which from more googling is a 1A Fuse
https://www.manualslib.com/manual/1063274/Sony-Rdr-Gx300.html?page=116

Ah, and of course replacing the fuse won´t help as it blew for a reason probably
« Last Edit: January 28, 2020, 01:01:21 pm by goaty »
 
The following users thanked this post: deisenberg

Offline deisenbergTopic starter

  • Contributor
  • Posts: 40
  • Country: ca
  • Seriously I have no clue.
Re: Identifying a fuse
« Reply #6 on: January 28, 2020, 02:06:41 pm »
Here is the PCB with out the pico fuse. Green fuse above it with a red strip is the other that is dead as well. P301 9-885-036-14 LINK, IC.
 

Offline deisenbergTopic starter

  • Contributor
  • Posts: 40
  • Country: ca
  • Seriously I have no clue.
Re: Identifying a fuse
« Reply #7 on: January 28, 2020, 02:08:08 pm »
Thanks your google fu is much better then mine!

Also the problem was caused by myself, I tried to power an Adriuno mega from the 11v rail and that's when the -11v stopped working. It's possible I shorted it out.


edit: For anyone else that has this issue

P301 9-885-036-14 LINK, IC is a 20N2000 is a skygate 2a/250 fuse.
P501 9-885-024-65 LINK, IC is a 20N1000 is a skygate 1a/250 fuse.
I used https://www.jotrin.com/ to pull up the details.

Thanks everyone for your help!
« Last Edit: January 28, 2020, 02:15:13 pm by deisenberg »
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf