Need full firmware (full dump flash) oscilloscope Atten ADS 1062CML

[routerfan]

Hi routerfan
Thanks for your help with the .rar file 

I'm trying, and i've a question.
I've made the connection cable from programmer to Lattice JTAG connector.
In the oscilloscope mainboard i've not found the connections in red (see the image attached). I not understand if the scheme is of all the connection cable or if i've to made only the connection to the programmer (and the connection between BF531 JTAG and Lattice JTAG connectors are in the mainboard).

Please excuse me for this question, but i haven't any electric scheme of the mainboard, and i don't want to make damages.
Can you help me please?

Hi alexitaly
 These lines are not ready-made, you need to connect them with a cable, I use DuPont cable.

[alexitaly]

Hi routerfan,
i've made and verified the JTAG cable, but the software give me the message "FAILED TO INITIALIZE JTAG CHAIN".
I've controlled the cable and the sw settings, the ftdi drivers, but i haven't obtained any result.
In these days i will continue to try... if someone has any idea i'm grateful.

[routerfan]

Hi routerfan,
i've made and verified the JTAG cable, but the software give me the message "FAILED TO INITIALIZE JTAG CHAIN".
I've controlled the cable and the sw settings, the ftdi drivers, but i haven't obtained any result.
In these days i will continue to try... if someone has any idea i'm grateful.

Hi alexitaly，

I don't know at which step you verified the cable. If the cable is normal and the drive is normal, there should be no problem.
 Another thing to note is that ADSP_BF531_LQFP.bsdl and LCMXO256C_XXT100.bsdl have you specified the paths? It's important

[tv84]

I hope you are making progress. 

When you need my help please pm as I might not come here often.

[alexitaly]

Hi routerfan, excuse me for the delay with which i answer.
Unfortunately, in this period i got some problems, the last of which is the lost of my work due to covid consequences (there are no job orders in the company where i work).
Because of this, i have to postpone the memory dump: infact, if I make a mistake and do damage, I would have great financial problems to fix, and I need the DSO to do some small jobs that are now useful for taking money.
As soon as I can I will help you, now I hope you will understand me.
Excuse me, thanks for your attention.

[tv84]

Excuse me, thanks for your attention.

Totally excused!   

I wish all the best and good luck in getting a new job.

Stay safe!

[routerfan]

Excuse me, thanks for your attention.

Totally excused!   

I wish all the best and good luck in getting a new job.

Stay safe!

Hi alexitaly
  Life in various industries is not so good this year, I hope you will go through this difficult period smoothly, nothing else matters
  I have set aside the oscilloscope. After all, there are still things to deal with. This may be the trouble for adults. But I still did not give up. Some time ago, an old oscilloscope of this model was on sale. I missed it. But it doesn't matter, there is a chance next time.
  Thank you again, including TV84 for helping me, I will come back to see if I have time.
   Good luck and health!

[hlj.pycad]

hi, tv84, I just got this old ads1102cal on a flea market, and I got almost the same system status of "bithead9" got, so I decide to update the oscilloscope.
I download the latest firmware of siglent 1102cnl firmware, which is V6.01.01.21R2, with the name "P21R2.ADS", but the machine refuse to flash the firmware, saying "product type is not accordant"
I wonder where I can download this old "SDS1000CNL_SSP_V100R005B01D02P13.ADS" to give a try... or I just missed some manoeuver to bypass the product type chek?


***EDIT*****
I think the V6.01 is not for CNL, those V5.0 work fine, but the some fireware didn't come with the CFG file and instruction, wandered around a bit before I learn that.