Author Topic: Need help for a repair for the Rigol DG1022A  (Read 894 times)

0 Members and 1 Guest are viewing this topic.

Offline thephantom1492

  • Contributor
  • Posts: 6
  • Country: ca
Need help for a repair for the Rigol DG1022A
« on: March 17, 2019, 05:30:39 am »
Hello everyone
I need help to figure out a proper replacement for the common mode choke for the channel 1 of my signal generator.
Mine is just... a dead short so no mesurement is possible.

<=== This is the choke, as seen there: ===>


edit: need mostly the inductance value, or a likelly range...

edit 2: specify siggen
« Last Edit: March 17, 2019, 10:44:00 pm by thephantom1492 »
 

Offline thedoc298

  • Contributor
  • Posts: 28
  • Country: us
Re: Need help for a repair for the Rigol DG1022A
« Reply #1 on: March 17, 2019, 12:00:43 pm »
It should measure as dead short or very low.  What is the problem with scope...?
 

Offline thephantom1492

  • Contributor
  • Posts: 6
  • Country: ca
Re: Need help for a repair for the Rigol DG1022A
« Reply #2 on: March 17, 2019, 10:42:38 pm »
dead short on all 4 pins on that common mode choke. Channel 1 output is null.

Removed the choke and replaced by 2 wires and the siggen work, but obiviously the removal of a component is not ideal.

And, that choke is short on all pins.

edit: the DG1022A is a siggen, not a scope
 

Offline thedoc298

  • Contributor
  • Posts: 28
  • Country: us
Re: Need help for a repair for the Rigol DG1022A
« Reply #3 on: March 18, 2019, 03:04:06 am »
So the choke was shorted, and you replaced the shorted choke with wires (another short) and it works.

So don't you think your choke is open and not shorted..?
 

Offline Dacke

  • Regular Contributor
  • *
  • Posts: 76
  • Country: us
Re: Need help for a repair for the Rigol DG1022A
« Reply #4 on: March 18, 2019, 03:40:21 am »
This is the one I used in my DG1022 as I had the same thing happen to mine:

https://www.digikey.com/product-detail/en/wurth-electronics-inc/744235601/732-4221-1-ND/3672769

And yeah,  the windings in the choke got blown open due to my own stupidity.   The sig gen works fine now.

 
The following users thanked this post: RobertHolcombe

Offline thephantom1492

  • Contributor
  • Posts: 6
  • Country: ca
Re: Need help for a repair for the Rigol DG1022A
« Reply #5 on: March 18, 2019, 04:23:40 am »
Here mine had started to be weird at time, showing overload at time that I wondered why... and then I fed 35V from a subwoofer to the ground (fricking amp seems to be positivelly grounded, or something, the red was the ground !

I hope it will fix the other issue I had at the same time.

edit: thanks!
 

Offline thephantom1492

  • Contributor
  • Posts: 6
  • Country: ca
Re: Need help for a repair for the Rigol DG1022A
« Reply #6 on: March 20, 2019, 04:08:36 am »
Good news! I got a reply from rigol itself!

That choke is ACM4532-901-2P, an alternative is ACM4532-801-2P.

Both currently unavailable, we'll see if it come stock soon.
 

Offline Housedad

  • Frequent Contributor
  • **
  • Posts: 513
  • Country: us
At least I'm still older than my test equipment
 

Offline thephantom1492

  • Contributor
  • Posts: 6
  • Country: ca
Re: Need help for a repair for the Rigol DG1022A
« Reply #8 on: April 18, 2019, 05:00:24 am »
A bit old (been quite busy) but for future reference:

ACM4532-901-2P

ACM: series

4532: size, 4.5x3.2mm

901: impedance at 100MHz: 900Ω

2P: number of lines


I can't find the ACM4532-901-2P exact specs, but the 801 is:
800Ω@100MHz, DC resistance: 100mΩ, rated current: 1A, rated voltage: 50V
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf