| Electronics > Repair |
| Repair and upgrade DPO7104 -->DPO7354 |
| << < (3/4) > >> |
| sprit:
Hi my vxWork post screen here romPost: I am alive . uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu �omPost: L2 cache turned on. romPost: I am alive . uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu romPost: L2 cache turned on. romPost: MPC107 Walking-one passed. romPost: MPC107 configuration passed. romPost: Intel21555 PCITOPCI bridge configuration passed. romPost: PERFORMING ROM CHECKSUM TEST... romPost: ROM checksum passed. romPost: PERFORMING DRAM CELL TEST... romPost: Enabling data cache... romPost: Data cache enabled. romPost: Enabling instruction cache... romPost: Instruction cache enabled. romPost: DRAM Cell test passed. romPost: PERFORMING DRAM MARCH TEST WITH CACHE OFF... romPost: Disabling data Cache... romPost: Data cache disabled. romPost: Disabling instruction cache... romPost: Instruction cache disabled. romPost: Writing address to each *address... romPost: Reading address from each *address... romPost: DRAM march test passed... romPost: PERFORMING DRAM MARCH TEST WITH CACHE ON... romPost: Enabling data cache... romPost: Data cache enabled. romPost: Enabling instruction cache... romPost: Instruction cache enabled. romPost: Writing address to each *address... romPost: Reading address from each *address... romPost: DRAM march test passed... romPost: PERFORMING DRAM WALKING-ONE TEST... romPost: DRAM Walking-one test passed. romPost: PERFORMING NV-MEMORY WALKING-ONE TEST... romPost: NV-MEMORY Walking-one test passed. romPost: Disabling data Cache... romPost: Data cache disabled. romPost: Disabling instruction cache... romPost: Instruction cache disabled. romPost: Enabling instruction cache... romPost: Instruction cache enabled. romPost: POWER-UP DIAGNOSTIC COMPLETE. Hel VxWorks System Boot Copyright 1984-1996 Wind River Systems, Inc. CPU: Tektronix HPP - IBM 750CXe Version: 5.3.1 BSP version: 2.0.1.10 Creation date: Sep 30 2003, 07:53:07 Press any key to stop auto-boot... 0 auto-booting... boot device : sm processor number : 0 file name : c:/vxboot/vxWorks.st inet on backplane (b): 192.168.0.1:ffffff00 host inet (h) : 192.168.0.2 gateway inet (g) : 192.168.0.1 flags (f) : 0x1008 target name (tn) : tds7000 startup script (s) : c:/vxboot/topscript.hw Initializing backplane net with anchor at 0x1e80000... done. Backplane anchor at 0x1e80000... Attaching network interface sm0... done romPost: I am alive . uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu romPost: L2 cache turned on. � romPost: I am alive . uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu romPost: L2 cache turned on. romPost: MPC107 Walking-one passed. romPost: MPC107 configuration passed. romPost: Intel21555 PCITOPCI bridge configuration passed. romPost: PERFORMING ROM CHECKSUM TEST... romPost: ROM checksum passed. romPost: PERFORMING DRAM CELL TEST... romPost: Enabling data cache... romPost: Data cache enabled. romPost: Enabling instruction cache... romPost: Instruction cache enabled. romPost: DRAM Cell test passed. romPost: PERFORMING DRAM MARCH TEST WITH CACHE OFF... romPost: Disabling data Cache... romPost: Data cache disabled. romPost: Disabling instruction cache... romPost: Instruction cache disabled. romPost: Writing address to each *address... romPost: Reading address from each *address... romPost: DRAM march test passed... romPost: PERFORMING DRAM MARCH TEST WITH CACHE ON... romPost: Enabling data cache... romPost: Data cache enabled. romPost: Enabling instruction cache... romPost: Instruction cache enabled. romPost: Writing address to each *address... romPost: Reading address from each *address... romPost: DRAM march test passed... romPost: PERFORMING DRAM WALKING-ONE TEST... romPost: DRAM Walking-one test passed. romPost: PERFORMING NV-MEMORY WALKING-ONE TEST... romPost: NV-MEMORY Walking-one test passed. romPost: Disabling data Cache... romPost: Data cache disabled. romPost: Disabling instruction cache... romPost: Instruction cache disabled. romPost: Enabling instruction cache... romPost: Instruction cache enabled. romPost: POWER-UP DIAGNOSTIC COMPLETE. Hel VxWorks System Boot Copyright 1984-1996 Wind River Systems, Inc. CPU: Tektronix HPP - IBM 750CXe Version: 5.3.1 BSP version: 2.0.1.10 Creation date: Sep 30 2003, 07:53:07 Press any key to stop auto-boot... 0 auto-booting... boot device : sm processor number : 0 file name : c:/vxboot/vxWorks.st inet on backplane (b): 192.168.0.1:ffffff00 host inet (h) : 192.168.0.2 gateway inet (g) : 192.168.0.1 flags (f) : 0x1008 target name (tn) : tds7000 startup script (s) : c:/vxboot/topscript.hw Initializing backplane net with anchor at 0x1e80000... done. Backplane anchor at 0x1e80000... Attaching network interface sm0... done it stuck here, the flag 0x1008 i cant change it to 0x1000, idk what to do now. Hope it can help |
| coromonadalix:
post the log in a file here's what ive tried This is what works for me in the nvram content boot device : sm sm processor number : 0 0 host name : host host file name : c:\vxBoot\vxWorks.st c:\vxBoot\vxWorks.st inet on ethernet (e) : 192.168.0.2:ffffff00 192.168.0.2:ffffff00 inet on backplane (b): 192.168.0.2:ffffff00 192.168.0.2:ffffff00 host inet (h) : 192.168.0.1 192.168.0.1 gateway inet (g) : 192.168.0.2 192.168.0.2 user (u) : anonymous anonymous ftp password (pw) (blank = use rsh): anonymous anonymous flags (f) : 0x1000 0x1000 some had to put 0x1008 in my case it did not help target name (tn) : target tds7000 this one should be tds7000, otherwise tekscope will not save settings startup script (s) : c:\vxBoot\dio_rst.vsh c:\vxboot\topscript.hw other (o) : this one play tricks had to put 0x0 or 0x0000 tekscope had some problems, some have put 0x1000 Still have doubts on the flags and other sections, if i put something else in the flag like 0x1008, tekscope stalls if i change other setting like 0x1000 tekscope starts but no traces of ch1 ch2 ..... |
| sprit:
Hi, thanks for the help. After doing that, what i should do now, normal reboot via start menu or command on teraterm? |
| sprit:
Haizz, its still stuck at normal. I find it quite strange because my serial screen still shows the same value on boot whether I remove or insert the battery in that Dalast. I don't know what's going on. The DPO screen keeps freezing and giving this error? Is it because of the Windows XP I installed on it? I downloaded the TDS software directly from the homepage, Latest version. Now I don't know where to go. :( |
| coromonadalix:
windows device manager ... what does it show, is there any error ? |
| Navigation |
| Message Index |
| Next page |
| Previous page |