Electronics > Repair
Siglent oscilloscope screen SHS1102 frozen
Alex2trois:
Bonjour Tautech,
Voici les nouvelles :
Il met environ 16 secondes à démarrer
Pour quelle raison l'écran était figé, je n'a pas de réponse à vous donner
Concernant la mise à jour :
J'ai testé avec de nombreuses clés usb (fat32 4K), l'appareil ne détecte rien
J'ai bien 5VCC sur la clé
Peut être une mauvaise soudure sur data+ ou data- ?
Merci, à bientot
Alexandre
Hello Tautech,
Here is the news:
It takes about 16 seconds to start
Why the screen was frozen, I have no answer to give you
Regarding the update:
I tested with many usb keys (fat32 4K), the device does not detect anything
I have 5VDC on the key
Maybe a bad solder on data+ or data-?
Thank you, see you soon
Alexander
tautech:
--- Quote from: Alex2trois on September 28, 2024, 05:34:59 pm ---Hello Tautech,
Here is the news:
It takes about 16 seconds to start
Why the screen was frozen, I have no answer to give you
Regarding the update:
I tested with many usb keys (fat32 4K), the device does not detect anything
I have 5VDC on the key
Maybe a bad solder on data+ or data-?
Thank you, see you soon
Alexander
--- End quote ---
Which version of firmware does Utility/System Status report ?
Are you operating from the battery or from the mains charger ?
Alex2trois:
Tautech,
ver_soft 3.01.02.02r7
ver_hard : 8-21-3.3
J'ai essayé de faire la mise à jour sur secteur 230/12V avec batterie et avec batterie seulement : sans succè :(
I tried to update on 230/12V sector with battery and with battery only: without success :(
Encore merci pour votre implication ;)
tautech:
Does SHS1102 power On/Off correctly ?
ver_soft 3.01.02.02r7 is first firmware and if possible it should be updated.
There may be a USB fault preventing you from updating however I would first suspect a incompatible USB stick.
Reformat others you have to FAT32 with 4k clusters and try them.
Place the ADS file from the firmware ZIP package into the root folder of the USB stick which makes it easy to find and navigate to.
https://int.siglent.com/upload_file/zip/firmware/Hand-held_oscilloscope/SHS1000_5.09.01.07_EN.zip
Alex2trois:
Bonjour Tautech,
J'ai une bonne nouvelle
J'ai eu de la chance :phew: : sans doute dessoudé involontairement en examinant toutes les soudures ou alors une mauvaise soudure sur le contrôleur usb...
J'ai téléchargé le datashet du ISP62BD, je pense que la patte 63 (D0) et 64 (D1) était en contact (court circuit) ou seulement la patte 63 (D1) sans contact, avec un peu de soudure et c'est parfait !
Maintenant dès que je mets une clé usb l'appareil me l'indique instantanément : "clé USB branchée" "clé USB débranchée" ;)
La mise à jour du firmware shs1000 5.09.01.07 s'est bien déroulée
Le temps de démarrage du shs 1102 est d'environ 16 secondes
Donc maintenant je suis en version software 5.09.01.07 et hardware version 8-21-3.6
Une autre question :
Que veut dire cfg ? Configuration peut être...
Un grand merci à Tautech et coromonadalix pour m'avoir consacré un peu de leurs temps :clap:
I have good news
I was lucky :phew: : probably unsoldered unintentionally while examining all the solders or a bad solder on the usb controller...
I downloaded the ISP62BD datasheet, I think that pin 63 (D0) and 64 (D1) were in contact (short circuit) or only pin 63 (D1) without contact, with a little soldering and it's Perfect !
Now as soon as I insert a USB key the device instantly tells me: “USB key plugged in” “USB key unplugged” ;)
Firmware update shs1000 5.09.01.07 went well
Boot time of shs 1102 is approximately 16 seconds
So now I am in software version 5.09.01.07 and hardware version 8-21-3.6
Another question:
What does cfg mean? Configuration can be...
A big thank you to Tautech and coromonadalix for devoting some of their time to me :clap:
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version