Author Topic: Sourcing a replacement transformer, LCD TV repair. (Read 10741 times)

wraper · « **Reply #50 on:** September 25, 2018, 02:43:51 pm »

Quote from: boba3 on September 25, 2018, 02:39:03 pm

putting the ZD604 and ZD605 back to their original position I find on one side of the r609 I have 13v and on the other side 0.9v

This completely contradicts with:

Quote

before R630 I have 78v, between R630 and R631 I have 38v, between R631 and R609 I have 38mv

wraper · « **Reply #51 on:** September 25, 2018, 02:45:16 pm »

Did you check ZD605 BTW, isn't it shorted by chance?

wraper · « **Reply #52 on:** September 25, 2018, 03:15:07 pm »

Also write part number of IC601, I don't know what it is.

boba3 · « **Reply #53 on:** September 25, 2018, 03:18:20 pm »

I had to get out of work. I will resume tomorrow. Thank you very much for your information and your patience. We'll talk tomorrow. good day

boba3 · « **Reply #54 on:** September 25, 2018, 03:21:40 pm »

Ic601=A6069H

boba3 · « **Reply #55 on:** September 25, 2018, 03:28:45 pm »

In R609 there is written 625

wraper · « **Reply #56 on:** September 25, 2018, 04:04:33 pm »

Quote from: boba3 on September 25, 2018, 03:21:40 pm

Ic601=A6069H

I checked the datasheet. It's strange they placed R609 at all. Seems it has 6.2M resistance. This IC actually takes startup current from pins 7,8 and pin 2 is for voltage detection only. Thus placement of R609 is weird but as it has a very high resistance it basically does nothing. As you said there was 38mV on pin 2 when IC was present, I assume that IC is either faulty ir you got counterfeit with something else inside. Where you bought the replacement IC?

http://www.semicon.sanken-ele.co.jp/sk_content/str-a606xh_ds_en.pdf

boba3 · « **Reply #57 on:** September 25, 2018, 04:51:29 pm »

Tomorrow I replace the components that I had removed each of their original poto and recheck. Honestly Ic601 after being exploded did not read what was written. It read only A .... H Then on the web I found it was A6069H. Actually I do not know if it's correct

wraper · « **Reply #58 on:** September 25, 2018, 10:32:49 pm »

Try measuring resistance between pin 2 and 3 of the IC.

boba3 · « **Reply #59 on:** September 26, 2018, 06:16:46 am »

Good morning, I checked the schematic of the power card you sent me and it corresponds to my card. I put all the components back to their initial position. now without ic601 I have between GND and before R609 13v, between GND and after R609 i have 0.9v. I checked the schematic of the A6069H and it seems to me that the GND is the pin 3, and the Vcc is the pin5. is it correct? between pin 2 and pin 3 I have about 1Mohm. between GND and pin 7/8 of IC 601 of the board I have 320v

boba3 · « **Reply #60 on:** September 26, 2018, 10:40:25 am »

Quote from: wraper on September 25, 2018, 02:43:51 pm

Quote from: boba3 on September 25, 2018, 02:39:03 pm
putting the ZD604 and ZD605 back to their original position I find on one side of the r609 I have 13v and on the other side 0.9v
This completely contradicts with:
Quote
before R630 I have 78v, between R630 and R631 I have 38v, between R631 and R609 I have 38mv

I have 0.9 without ic601 installed, and I have 38mv with ic 601 installed

wraper · « **Reply #61 on:** September 26, 2018, 11:35:05 am »

it's a bit confusing what you wrote in last 2 messages.

Quote

now without ic601 I have between GND and before R609 13v, between GND and after R609 i have 0.9v.

What do you have before R609 with IC installed?

boba3 · « **Reply #62 on:** September 26, 2018, 12:10:09 pm »

with ic installed, before R609 i have 38mv

wraper · « **Reply #63 on:** September 26, 2018, 12:23:37 pm »

Pin 2 is input, so it should not pull voltage down this lot. It has a 6.4V zener diode on it so it what it should be limited to. 38mV certainly seems as indication that IC is either faulty or counterfeit.

boba3 · « **Reply #64 on:** September 26, 2018, 12:38:14 pm »

ok, I will get another one. if this has burned up there is still something wrong with this card? I removed ic and in pin 2 I have 13v but in the 5 i continue to have 0.9v. Is it normal?

wraper · « **Reply #65 on:** September 26, 2018, 01:32:34 pm »

Quote from: boba3 on September 26, 2018, 12:38:14 pm

ok, I will get another one. if this has burned up there is still something wrong with this card? I removed ic and in pin 2 I have 13v but in the 5 i continue to have 0.9v. Is it normal?

Yes, it's normal. Unless there is something wrong with parts connected to pins 7,8, it should not fail. And if it fails, most likely it will blow up. Hence I suspect counterfeit, there are plenty at shady sources.

boba3 · « **Reply #66 on:** September 26, 2018, 02:11:47 pm »

can you advise me where to buy it?

boba3 · « **Reply #67 on:** September 27, 2018, 02:24:48 pm »

good morning, when I get ic new, can I check it somehow before installing it?

wraper · « **Reply #68 on:** September 27, 2018, 03:25:34 pm »

just solder it in

boba3 · « **Reply #69 on:** September 28, 2018, 05:58:27 pm »

hi, I replaced ic. now I have 5v, but there is a problem in the PE0982 tab V28A001292A1. because when I connect it I'm 5v volts to 0. Is there a short circuit in the part of 5v. Is there a datascheet for this card?

boba3 · « **Reply #70 on:** October 04, 2018, 06:44:50 pm »

hello,
the board at the desk, in addition to having 5 volts must have other power supplies?


EEVblog Main Site	EEVblog on Youtube	EEVblog on Twitter	EEVblog on Facebook	EEVblog on Odysee

Author Topic: Sourcing a replacement transformer, LCD TV repair. (Read 10741 times)

Share me