Electronics > Repair
Tektronix CSA-8000 / TDS-8000 repair experiences?
<< < (7/13) > >>
tpsimon:
Hey,
Mine looks very similar. (I am just using D drive instead of C)

--- Code: ---UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU

romPost: MPC106  Walking-one passed.

romPost: MPC106 configuration passed.

romPost: First PCI access  passed.

romPost: PC87560 Walking-one passed.

romPost: PC87560 configuration passed.

romPost: DEC21554 configuration passed.


romPost: PERFORMING ROM CHECKSUM TEST...

romPost: ROM checksum passed.


romPost: PERFORMING DRAM CELL TEST...

romPost: Enabling data cache...
romPost: Data cache enabled.
romPost: Enabling instruction cache...
romPost: Instruction cache enabled.

romPost: DRAM Cell test passed.
romPost: Disabling data Cache...
romPost: Data cache disabled.
romPost: Disabling instruction cache...
romPost: Instruction cache disabled.

romPost: PERFORMING DRAM MARCH TEST WITH CACHE OFF...
romPost: Writing address to each *address...
romPost: Reading address from each *address...
romPost: DRAM march test passed...

romPost: PERFORMING DRAM MARCH TEST WITH CACHE ON...

romPost: Enabling data cache...
romPost: Data cache enabled.
romPost: Enabling instruction cache...
romPost: Instruction cache enabled.
romPost: Writing address to each *address...
romPost: Reading address from each *address...
romPost: DRAM march test passed...

romPost: PERFORMING DRAM WALKING-ONE  TEST...

romPost: DRAM Walking-one test passed.

romPost: PERFORMING NV-MEMORY WALKING-ONE  TEST...

romPost: NV-MEMORY Walking-one test passed.
romPost: Disabling data Cache...
romPost: Data cache disabled.
romPost: Disabling instruction cache...
romPost: Instruction cache disabled.
romPost: Enabling instruction cache...
romPost: Instruction cache enabled.


romPost: POWER-UP DIAGNOSTIC COMPLETE.

Hel











                            VxWorks System Boot



Copyright 1984-1996  Wind River Systems, Inc.






CPU: Tektronix HPP - PowerPC 740

Version: 5.3.1

BSP version: 1.0.3.0

Creation date: Jun 28 2000, 16:52:12





Press any key to stop auto-boot...

 1
 0

auto-booting...



boot device          : sm

processor number     : 0

host name            : host

file name            : d:\progra~1\tdscsa~1\firmware\vxWorks.st

inet on ethernet (e) : 192.168.0.2:ffffff00

inet on backplane (b): 192.168.0.2:ffffff00

host inet (h)        : 192.168.0.1

gateway inet (g)     : 192.168.0.2

user (u)             : anonymous

ftp password (pw)    : anonymous

flags (f)            : 0x1008

target name (tn)     : target

startup script (s)   : d:\progra~1\tdscsa~1\firmware\dio.vsh

other (o)            : nvfs=0x1000


Initializing backplane net with anchor at 0x1e80000... done.

Backplane anchor at 0x1e80000... Attaching network interface sm0... done

done.

Attaching network interface lo0... done.

PC1 dio device driver installed
Attaching DIO client... done.

Loading d:\progra~1\tdscsa~1\firmware\vxWorks.st...1771964

Starting at 0x200000...


Initializing backplane net with anchor at 0x1de0000... done.

Backplane anchor at 0x1de0000... Attaching network interface sm0... done

done.

PC1 dio device driver installed
Attaching network interface lo0... done.


Adding 6006 symbols for standalone.

 


 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]

 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]

 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]

      ]]]]]]]]]]]  ]]]]     ]]]]]]]]]]       ]]              ]]]]         (R)

 ]     ]]]]]]]]]  ]]]]]]     ]]]]]]]]       ]]               ]]]]           

 ]]     ]]]]]]]  ]]]]]]]]     ]]]]]] ]     ]]                ]]]]           

 ]]]     ]]]]] ]    ]]]  ]     ]]]] ]]]   ]]]]]]]]]  ]]]] ]] ]]]]  ]]   ]]]]]

 ]]]]     ]]]  ]]    ]  ]]]     ]] ]]]]] ]]]]]]   ]] ]]]]]]] ]]]] ]]   ]]]] 

 ]]]]]     ]  ]]]]     ]]]]]      ]]]]]]]] ]]]]   ]] ]]]]    ]]]]]]]    ]]]]

 ]]]]]]      ]]]]]     ]]]]]]    ]  ]]]]]  ]]]]   ]] ]]]]    ]]]]]]]]    ]]]]

 ]]]]]]]    ]]]]]  ]    ]]]]]]  ]    ]]]   ]]]]   ]] ]]]]    ]]]] ]]]]    ]]]]

 ]]]]]]]]  ]]]]]  ]]]    ]]]]]]]      ]     ]]]]]]]  ]]]]    ]]]]  ]]]] ]]]]]

 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]

 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]       Development System

 ]]]]]]]]]]]]]]]]]]]]]]]]]]]]

 ]]]]]]]]]]]]]]]]]]]]]]]]]]]       VxWorks version 5.3.1

 ]]]]]]]]]]]]]]]]]]]]]]]]]]       KERNEL: WIND version 2.5

 ]]]]]]]]]]]]]]]]]]]]]]]]]       Copyright Wind River Systems, Inc., 1984-1997


                               CPU: Tektronix HPP - PowerPC 740.  Processor #0.

                              Memory Size: 0x2000000.  BSP version 1.0.3.5.

                             WDB: Ready.


usrNvFsInit: NAME=/nvram BASE=0xfd0ff100 BPB=512 BPT=8 NB=8 BO=0

nvfs: STATUS: Mounting existing NVRAM file system

KERNEL: THERMAL CONTROL INITIATED

Executing startup script d:\progra~1\tdscsa~1\firmware\dio.vsh ...

dbFsIoctl: invalid code 3

cd "c:/progra~1/tdscsa~1/firmware"

value = 0 = 0x0

*0xfec00000 = 0x04b00080;*0xfee00000 = 0x17009002

ppp_parms + 0xfe84f680 = 0xfec00000: value = 78643328 = 0x4b00080

ppp_parms + 0xfea4f680 = 0xfee00000: value = 385912834 = 0x17009002

*0xfec00000 = 0x88a10080;*0xfee00000 = 0x01800000

ppp_parms + 0xfe84f680 = 0xfec00000: value = -2002714496 = 0x88a10080 = ppp_parms + 0x8865f700

ppp_parms + 0xfea4f680 = 0xfee00000: value = 25165824 = 0x1800000

*0xfe008002 = 0;*0xfe00800e = 0;*0xfe008012 = 0

ppp_parms + 0xfdc57682 = 0xfe008002: value = 0 = 0x0

ppp_parms + 0xfdc5768e = 0xfe00800e: value = 0 = 0x0

ppp_parms + 0xfdc57692 = 0xfe008012: value = 0 = 0x0

symSyncTimeoutSet 600000

value = 600000 = 0x927c0

ld <hi32.o

value = 31002016 = 0x1d90da0 = Hi32SystemProcessorBoard + 0xa98

Hi32SystemProcessorBoard = 1

Hi32SystemProcessorBoard = 0x1d90308: value = 1 = 0x1

CmdDspDevName = "/dev/cmddsp0"

new symbol "CmdDspDevName" added to symbol table.

CmdDspDevName = 0x1d90cc0: value = 31002464 = 0x1d90f60 = CmdDspDevName + 0x2a0

hi32Drv

value = 0 = 0x0

hi32DevCreate CmdDspDevName,0x80006000,0xa0000000,3

value = 0 = 0x0

ld <cmddsp.o

value = 31000320 = 0x1d90700 = Hi32SystemProcessorBoard + 0x3f8

ld <acqdsp.o

value = 31000800 = 0x1d908e0 = Hi32SystemProcessorBoard + 0x5d8

ld <diagcmddsp.o

value = 31008192 = 0x1d925c0

ld <diagModule_wmp.o

value = 31007552 = 0x1d92340

ld < systemLibraryCode.o

value = 31007104 = 0x1d92180

CSSDefaultDioDisable=0

CSSDefaultDioDisable = 0x1b20480: value = 0 = 0x0

semInitForQueueCheckLogMsg

value = 31001312 = 0x1d90ae0 = Hi32SystemProcessorBoard + 0x7d8

ld < nvSysLib.o

value = 30999648 = 0x1d90460 = Hi32SystemProcessorBoard + 0x158

ld < bucket.o

value = 31003968 = 0x1d91540 = CmdDspDevName + 0x880

MathMeasCreateMappingFcns = 1

MathMeasCreateMappingFcns = 0x1aa60b8: value = 1 = 0x1

TmgrExecuteAllMappingFunctionsEnable=1

TmgrExecuteAllMappingFunctionsEnable = 0x1aa2694: value = 1 = 0x1

ld < as.o

value = 28451456 = 0x1b22280

ld < ifcProxy.o

value = 28450880 = 0x1b22040

acqCheckForCmdDsp=1

new symbol "acqCheckForCmdDsp" added to symbol table.

acqCheckForCmdDsp = 0x1d90660: value = 1 = 0x1

ld < rtlLibTarget.o

value = 28340096 = 0x1b06f80

ld < slotMgrLightLibTarget.o

value = 28287200 = 0x1afa0e0

sysExtMemAddToPool memSysPartId ,0x02000000 ,0x02000000

value = 0 = 0x0

MathMeasDisableParseExpr = 1

new symbol "MathMeasDisableParseExpr" added to symbol table.

MathMeasDisableParseExpr = 0x3fff400: value = 1 = 0x1

use100Breakpoints=1

use100Breakpoints = 0x14f6e34: value = 1 = 0x1

pWfmMemPool=0

pWfmMemPool = 0x1abf1f0: value = 0 = 0x0

AcqLibFourChannelProto = 0

new symbol "AcqLibFourChannelProto" added to symbol table.

AcqLibFourChannelProto = 0x3fff3a0: value = 0 = 0x0

AcqExecHardWireChannelSources = 0

AcqExecHardWireChannelSources = 0x119ecfc: value = 0 = 0x0

doTekprobeExec=1

doTekprobeExec = 0x128cbc4: value = 1 = 0x1

pDbDev = ramDevCreate(0, 640, 1024, 1024, 0)

new symbol "pDbDev" added to symbol table.

pDbDev = 0x3f5f2c0: value = 67105536 = 0x3fff300

pDBfs  = dosFsMkfs("/db", pDbDev)

new symbol "pDBfs" added to symbol table.

pDBfs = 0x3f5dba0: value = 66449888 = 0x3f5f1e0

copy ("TDS666.DBF", "/db/TDS666.DBF")

value = 0 = 0x0

dbPath = "/db/"

new symbol "dbPath" added to symbol table.

dbPath = 0x3f5daa0: value = 66444064 = 0x3f5db20 = dbPath + 0x80

wfmMemInit 0

value = 55695744 = 0x351d980

jNVInitMgrs

value = 0 = 0x0

TmgrInit(dbPath)

value = 0 = 0x0

rtlInit

value = 0 = 0x0

MathMeasCreateTheMathandMeasurementLibraries

value = 50112544 = 0x2fca820

initAcqMapper

value = 50083584 = 0x2fc3700

autosetMapInit

value = 50083168 = 0x2fc3560

mathMapperInit

value = 0 = 0x0

initUtilityMapper

value = 50076320 = 0x2fc1aa0

initWfmXmtrMapper

value = 50072160 = 0x2fc0a60

commInit__Fv

value = 0 = 0x0

JanusProxyInit

value = 50038272 = 0x2fb8600

acqExecAllocUploadBuffers

undefined symbol: acqExecAllocUploadBuffers


Done executing startup script d:\progra~1\tdscsa~1\firmware\dio.vsh

KERNEL:  RUNNING TIME SLICED AT 10 TICKS PER SLICE!

->

--- End code ---
But I think I see what's wrong. I'll copy the OS over to a fresh drive and let you know, because everything is on the D: drive right now, and it seems that the code needed it to be on the C: drive.

Simon

Edit:

It seems to make no difference if I change the .vsh file.

Edit 2:

I will just wait for the board to come in tomorrow and see what it does.
tpsimon:
Got the whole scope working! Getting some Optical Modulators tomorrow so that I can mess with the scope.

Simon
ID10TError:
Hello Everyone,

My boss bought a CSA8000 off of eBay that had a failed hard drive. He asked me to put a new SATA hard drive in it and install Windows 2000. I got a little back plane converter to put in a SATA drive in the place if the IDE. Here is what I have so far. The unit came to me, failed hard drive, no video on the display (works with external monitor), drive B error at boot up, PXE boot (no hard drive seen), says it will enter setup when F2 is pressed (never goes into setup). CD player does not open.

So, I downloaded a BIOS update for Intel BL440ZX board from the Intel site. Put it on a bootable floppy and booted the system up with the floppy. It came up and ran the BIOS update (big mistake). Now when I try to boot it up, there is nothing. No display, no boot sounds, no post, etc. I remove the CMOS battery, nothing. I set the CMOS jumper to pins 2/3 from 1/2, still nothing.

I read somewhere after the fact not to update the BIOS using firmware updates from the Intel site. That is what I did. How can I get this thing back with the right BIOS firmware so it will somewhat boot again?

PS - If I take the jumper off the pins and power on, it will try to read the floppy drive. Won't boot from it, but I believe that setting is to restore a BIOS if I had the proper files.

Thanks for your help!

ID10T Error
EB5AGV:

--- Quote from: tpsimon on June 28, 2017, 01:18:52 am ---Got the whole scope working! Getting some Optical Modulators tomorrow so that I can mess with the scope.

Simon

--- End quote ---

Great news!!!

Please, try the compensation procedure for the mainframe (and any plug-in you may have) and let us know the results. If the unit passes, you have got a good one  :-+

Regards,

Jose
ID10TError:
Anyone have any thoughts on how I can re-flash the BIOS and where I can get the required BIOS files?

Thanks,
Navigation
Message Index
Next page
Previous page
There was an error while thanking
Thanking...

Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod