Electronics > Repair
Tektronix VM6000 Firmware
iAleks:
My hdd image take 11Gb after recovery, but tekscope program after start create files (here C:\TekScope\wfmObj, i delete this files from hdd image for decrease image size) which occupy ~10Gb, i think you need try larger size SSD.
--- Code: --- Содержимое папки G:\TekScope\wfmObj
14.02.2013 01:10 <DIR> .
14.02.2013 01:10 <DIR> ..
17.01.2008 04:38 536 870 912 CH1.Curve
14.02.2013 01:00 6 422 528 CH1.FF
17.01.2008 04:38 65 536 CH1.Preamble
17.01.2008 04:38 536 870 912 CH2.Curve
14.02.2013 01:00 6 422 528 CH2.FF
17.01.2008 04:38 65 536 CH2.Preamble
17.01.2008 04:38 536 870 912 CH3.Curve
14.02.2013 01:00 6 422 528 CH3.FF
17.01.2008 04:38 65 536 CH3.Preamble
17.01.2008 04:38 536 870 912 CH4.Curve
14.02.2013 01:00 6 422 528 CH4.FF
17.01.2008 04:38 65 536 CH4.Preamble
14.02.2013 01:00 4 096 000 000 Digital.Events
14.02.2013 01:00 65 536 Digital.Preamble
17.01.2008 04:38 536 870 912 MATH1.Curve
14.02.2013 00:59 6 422 528 MATH1.FF
17.01.2008 04:38 65 536 MATH1.Preamble
17.01.2008 04:38 536 870 912 MATH2.Curve
14.02.2013 00:59 6 422 528 MATH2.FF
17.01.2008 04:38 65 536 MATH2.Preamble
17.01.2008 04:38 536 870 912 MATH3.Curve
14.02.2013 00:59 6 422 528 MATH3.FF
17.01.2008 04:38 65 536 MATH3.Preamble
17.01.2008 04:38 536 870 912 MATH4.Curve
14.02.2013 00:59 6 422 528 MATH4.FF
17.01.2008 04:38 65 536 MATH4.Preamble
17.01.2008 04:38 536 870 912 REF1.Curve
14.02.2013 00:59 6 422 528 REF1.FF
17.01.2008 04:38 65 536 REF1.Preamble
17.01.2008 04:38 536 870 912 REF2.Curve
14.02.2013 00:59 6 422 528 REF2.FF
17.01.2008 04:38 65 536 REF2.Preamble
17.01.2008 04:38 536 870 912 REF3.Curve
14.02.2013 00:59 6 422 528 REF3.FF
17.01.2008 04:38 65 536 REF3.Preamble
17.01.2008 04:38 536 870 912 REF4.Curve
14.02.2013 00:59 6 422 528 REF4.FF
17.01.2008 04:38 65 536 REF4.Preamble
38 файлов 10 616 373 248 байт
2 папок 51 347 365 888 байт свободно
--- End code ---
squadchannel:
ialeks is right, the HDD may be too small.
What kind of SSD are you using? An actual SATA/PATA SSD? Or something with a bridge IC?
need at least 64GB.
Also, how did you run the recovery image? may have to burn it to a CD and boot it.
sprit:
--- Quote from: squadchannel on October 31, 2024, 09:09:35 am ---ialeks is right, the HDD may be too small.
What kind of SSD are you using? An actual SATA/PATA SSD? Or something with a bridge IC?
need at least 64GB.
Also, how did you run the recovery image? may have to burn it to a CD and boot it.
--- End quote ---
Hi squadchanel
with iAleks's file, the os boot normaly without problem, but the scope keepping crash like that, i will go out and buy another SSD/HDD then try it again. It could also be because my drive has too little capacity.I use the SSD directly without going through any adapter, meaning it is attached directly to the sata port on the device.
The file you gave me was backed up from Acronis software, I used that software to burn to my ssd.
squadchannel:
Are you booting directly from an recovery image?
you are not trying to create an acronis bootable disk or something and load it from there?
coromonadalix:
ill chime one last time for sprit bruh
i gave you links for a long thread where you could find many drivers, i posted and others have posted them,
the best scenarios where :
install os from scratch, after nvram reconfigurations, if you see vxwork ticking message at the end, and do answer all device manager errors, and finally install tek scope,
if the pc side is not ok scope will always crash
a 16gb drive can work the originals where around 30 gb and almost half empty
stop being stubborn, and do some read, you had answers for a long time ...
good luck bruh
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version