Author Topic: Anyone experience with 28V microwave relays ? Bought one, coil current ~ 150mA ?  (Read 1012 times)

0 Members and 1 Guest are viewing this topic.

Offline prutser

  • Contributor
  • Posts: 32
  • Country: nl
I have no expererience  with microwave relais. Bought 2 used 18GHz relays. One from Sivers/Philips, draws about 40mA  @ 28V
The other one from Microwave Associates (brand seems to be sold regularly on Ebay, but I cannot find any details)
Coil does 160mA @ 28V which is over 4 Watts.

Does anyone knows if this is usual for those kines of relays ?
 

Online TheMG

  • Frequent Contributor
  • **
  • Posts: 758
  • Country: ca
It can be normal depending on the design and size of the relay. Some have quite large and multiple mechanical moving parts that require a stronger coil.
 

Online Bud

  • Super Contributor
  • ***
  • Posts: 5579
  • Country: ca
Maybe it was designed for fast switching with higher energizing voltage and then to lower holding voltage.
Facebook-free life and Rigol-free shack.
 

Offline radar_macgyver

  • Frequent Contributor
  • **
  • Posts: 596
  • Country: us
Some include a freewheel diode internally (HP/Keysight relays in particular), so polarity matters for those. If forward biased, current draw will be high.
 

Offline Whales

  • Super Contributor
  • ***
  • Posts: 1484
  • Country: au
    • Halestrom
Are the eBay ones cheap?  Crack one open and see what's inside.

I'd also try and verify that their coils have been wound correctly (thickness of wire + number of turns) for 28V.  Try hooking up the coil inputs to a power supply and slowly turn up the voltage until the relay clicks.  If it moves at only 3V then you know it's wound incorrectly, if it latches at a bigger fraction (eg 12V?) of the full 28V then it's probably wound correctly for 28V.

Offline cj

  • Contributor
  • Posts: 42
  • Country: nl
It might also be a bi-stable relais which only requires a short pulse to switch after that no power is required anymore. The polarity of the pulse determines which port is selected.

160mA @ 28V is excessive, as Bud says it may require a lower holding voltage.

I just measured a 28V SMA relay (Transco) and it draws 80mA @ 24V which should be about 90mA @ 28V and it holds fine at 12V 40mA.

CJ

« Last Edit: January 19, 2022, 10:15:26 pm by cj »
 

Online jonpaul

  • Super Contributor
  • ***
  • Posts: 1304
  • Country: fr
 
Most of the RF relays I have  do not include any  diode.

Check the resistance of the coil.

Perhaps the high current relay is not 28V but 12?

Jon





Jean-Paul (EE 1968, the Internet Dinosaur)
 

Offline Joel_Dunsmore

  • Regular Contributor
  • *
  • Posts: 159
  • Country: us
Check if it is a latching relay (someone mentioned bi-stable).  You will can switch it then remove the drive voltage and see if it holds the state.  If it does, then you can just send a pulse and to switch and switch back.  Some have both latching RF and DC (Keysight switches work this way) where there is also a relay on the DC side so when you apply the drive voltage, the relay snaps across and the DC contact is broken as the switch is moving. A couple of tests will sort out if you need to drive them all the time.
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf