Author Topic: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver  (Read 25553 times)

0 Members and 1 Guest are viewing this topic.

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« on: February 20, 2017, 11:30:32 pm »
A ham friend asked me to look at this rig. It has no output power on any of it's bands. After some research I found the following known issue -
Quote
the high IC ALC problem which resulted in no TX output power in the
radio. A few of use sent our radios to the same place here in the USA...
and this place replaced the same 6 smd resistors to fix the radio.

The 6 smd resistors that were replaced were...

R3034 & R3035 - 5.6K ohm
R3038, R3040, R3041, & R3042 - 6.8K ohm

All 6 of these are located on the bottom of the PA Unit.

https://beta.groups.yahoo.com/neo/groups/FT100/conversations/topics/36891

As you can see in the attachments, we see the true output power is about 0 dBm - there is a 40 dB attenuator inline to protect my spectrum analyzer in case it decides to work. The output power at this time should be +50 (100W). Frequency is off too.

Also, we can see the ALC indication is hard full scale, which is consistent with the known issue described in the research. So, we will see if I can repair it, I have no idea if it really has the same issue or not, but it looks promising. Will have to pull the PA board out next because the SMD resistors are on the bottom.  :-\

Oh, by the way, how about that microphone!  :wtf:
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Z80

  • Guest
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #1 on: February 21, 2017, 12:33:01 pm »
Be careful hooking the tx to your spectrum analyser, unless the attenuator is rated to handle 100W lots of swearing will follow should it suddenly spring to life.  A dummy load & power meter / scope is safer to see if the output is working.  That will also protect you output transistors as you seem to have an ALC fault.
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #2 on: February 21, 2017, 12:54:08 pm »
Be careful hooking the tx to your spectrum analyser, unless the attenuator is rated to handle 100W ...

Yea, it's rated for 100W - I know what I'm doing.  ;) Also, I want to see any small output emissions from the radio over the large bandwidth it covers so a spectrum analyzer is the tool to use. That's why I obtained that attenuator.
« Last Edit: February 21, 2017, 01:23:51 pm by xrunner »
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone, mrz80

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #3 on: February 21, 2017, 01:06:52 pm »
Getting ready to pull the PA board. The SMD's in question are on the bottom. The schematic shows them, indeed as 0.1% resistors, just for this one circuit. If they have drifted will have to order from Mouser I suppose, none on hand here.
« Last Edit: February 21, 2017, 01:18:14 pm by xrunner »
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #4 on: February 21, 2017, 11:23:53 pm »
Found the problem. R3042 (6.8k) was totally open. I replaced it with an 0805 I had (which is not 0.1%) and it started working. I will now order all the resistors in that area and replace them with new 0.1% resistors since these are all part of a known issue.

Also going to go through the alignment and do a complete clean-up of the radio.
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Z80

  • Guest
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #5 on: February 22, 2017, 11:50:57 am »
Yes that attenuator looks the part :-+  Nice job with the fix, did you find out what happened to the resistor?  Was it cracked?
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #6 on: February 22, 2017, 04:47:09 pm »
Yes that attenuator looks the part :-+  Nice job with the fix, did you find out what happened to the resistor?  Was it cracked?

Did not see any physical issues with it, it was just open. I just ordered all the resistors needed to make sure this issue does not appear again. Meanwhile, I'm going through the service alignments till the parts show up.
I told my friends I could teach them to be funny, but they all just laughed at me.
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #7 on: February 23, 2017, 03:52:50 pm »
Proceeding with alignment. Ran into a problem yesterday in that the procedure in the service manual for the HF idling current is just wrong, but you don't find out it can't be done the way it states until after you turn some pots, then you are screwed. But, fortunately I found some great info that allowed me to get past it. Here's what One person said -

Quote
Do not trust the service manual. Its junk. I have serviced the 100D thrice -
first for a blown driver 2SC2714, then changed controller card after a
lightning strike and lastly replaced a blown pair of MRF-255 with an
unmatched pair purchased from Singapore.

...

Hope this helps you and others. Finally I would like to point out the sheer
callousness of Yaesu in designing the 100D and charging a lot of money for
a service manual that is absolute trash.

http://comments.gmane.org/gmane.recreation.radio.hardware.yaesu.ft100/14148

So, I'm proceeding with the alignments and my SMD parts should arrive today.

I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #8 on: February 24, 2017, 01:24:08 pm »
Got the SMD resistor parts and installed them. Also applied fresh heat sink compound since the original was dry dust. Now will put the board back and finish the service alignments.
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #9 on: February 25, 2017, 01:04:07 am »
Well, I found more errors in the service manual.  >:(

On page 10 it has you inject a 1 kHz tone into the Mic line - levels of 1.5 mV, 3.0 mV, and 7.5 mV rms - to make some adjustments, however, these levels simply do not cause the stimulus desired. As the original settings are not far from other documented settings for this particular radio, I realized - oopsie - some technical writer put in a decimal place where it needn't be. The correct values are 15, 30, and 75 mV rms, which cause the correct response. Very sloppy Yaesu, very sloppy ...  :--

I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #10 on: February 26, 2017, 02:33:24 pm »
Now disassembling control head and mic. Plastic parts (that can) go into ultrasonic cleaner. Mic will receive brand new cord off Ebay. Other than that these parts are OK.
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Offline Radio Tech

  • Frequent Contributor
  • **
  • Posts: 942
  • Country: us
  • KC4UMO Buddy
    • Hobby Forum
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #11 on: February 27, 2017, 02:20:30 am »
Good job on bringing this one back to life.
 
The following users thanked this post: xrunner

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #12 on: February 27, 2017, 01:08:06 pm »
Good job on bringing this one back to life.

Thanks. As far as I can tell now I only need three more parts - the memory backup battery, a new speaker, and the replacement mic cord. Speaker is torn and in bad shape. Sourced a new one with the same mechanical dimensions on Mouser, also the CR2025 battery with solder tabs. Should be here in a few days. Owner is pretty excited.  :-+
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #13 on: February 27, 2017, 11:01:32 pm »
Prepping for backup battery replacement. According to the manual it's supposed to lose the user memories but not the service alignment memories when the battery is removed. My philosophy is - why take any chances?  :-// Let's tack on a temporary battery.
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #14 on: March 01, 2017, 03:23:42 pm »
Now fighting one last problem that started cropping up. It's another known issue - high SWR indication on the front panel when there is no such actual condition. It shuts down the transmitter, and on this radio it's happening on the UHF band. You can put a dummy load right on the radio's pigtail coax and it happens. So, I'm studying the way the problem was cured when people back in the day sent it back to Yaesu to get fixed.  :palm:
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Z80

  • Guest
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #15 on: March 01, 2017, 05:11:43 pm »
Don't you just hate it when that happens, you're ready to bolt the lid back on and up pops another problem.  Is that an early FT100?  I seem to remember the early ones were a bit flakey and Yaesu brought out a revised version which was much more stable.  I know what you mean with the service manuals, they are obviously as bad as the old ones then.  The service manual for my FT767 has a great section on aligning the IF board, unfortunately it is completely different to the one fitted to the radio.  Oh well  :-/O
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #16 on: March 02, 2017, 01:02:01 pm »
Don't you just hate it when that happens, you're ready to bolt the lid back on and up pops another problem.  Is that an early FT100?  I seem to remember the early ones were a bit flakey and Yaesu brought out a revised version which was much more stable.

Appears it's an early one, because it doesn't have added cures for the high SWR issue. I have made progress however. I added a copper braid as seen in pictures people made of the mods that Yaesu added when people sent in their radios to get fixed. See here -

http://k0lee.com/ft100/Newmods.htm

As of this morning high UHF SWR only happens when the radio is first turned on for a few minutes and then doesn't appear again. I have a few more things to add but it's 90% better now.

Quote
I know what you mean with the service manuals, they are obviously as bad as the old ones then.  The service manual for my FT767 has a great section on aligning the IF board, unfortunately it is completely different to the one fitted to the radio.  Oh well  :-/O

It sucks when you follow a step, and it is wrong.  >:( Go to this pot and adjust it until X is this value. Yea when you do that and nothing happens, you not only have no idea what they mean - the pot is now mis-adjusted and you have no idea how to correct it. I suppose you could mark a spot before you make a change, but sometimes even the slightest touch can mis-adjust something and that spot might not be exact enough to get it back. Fortunately there are people out there who document this stuff for the rest of us.  :clap:


I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #17 on: March 02, 2017, 03:40:19 pm »
Aha! I just found this smoked ceramic cap! Guess where - on the output of the VHF/UHF PA transistor.

It's supposed to be a 39 pF 500V cap but it tests as 0.2 ohms ... it's a wonder the thing is transmitting at all.  :popcorn:

Edit: Added better pic and schematic snip for anyone else that may need to repair this radio.
« Last Edit: March 02, 2017, 11:41:05 pm by xrunner »
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #18 on: March 04, 2017, 02:17:42 am »
I subbed out the bad 39 pF cap with a 33 pF ceramic I had on hand and now the SWR issue is totally gone.  :-+

The cap I used from my junk bin is not, however, rated at 500V, prolly only like 50V. I ordered the correct cap; but in the meantime the radio now appears to be functioning well. I plan on using it for the next few days until the last parts come in. Then I'll call my "customer" and he'll come and get it.
I told my friends I could teach them to be funny, but they all just laughed at me.
 

Offline brobers

  • Newbie
  • Posts: 2
  • Country: us
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #19 on: March 06, 2017, 06:28:15 am »
That microphone cord is typical for Yaesu. I have a couple of FT-1500s and a FT-100D that have all slowly fell apart like this.
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #20 on: March 06, 2017, 01:20:48 pm »
That microphone cord is typical for Yaesu. I have a couple of FT-1500s and a FT-100D that have all slowly fell apart like this.

It turned out to be useful while I was going through the service alignment because it allowed me to easily get to some of the wires and inject signals. Which reminded me I needed a way to easily do this again. Therefore ... I found this on Ebay and ordered one. As you can see it allows an in-out mic connection and also access to all six wires easily.



By the way, the owner of the FT-100 came over yesterday and I gave him a full demo, he was very pleased. Before he came over, last week I had also made a few JT65 contacts with it just to check it out and it succeed. However, it remains that this radio was not well designed and so the inherent issues with it remain (hot as a firecracker just receiving, bad output PA design). No telling how long it will go without other problems cropping up.
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Offline Hayden Perrine

  • Newbie
  • Posts: 1
  • Country: us
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #21 on: October 19, 2018, 05:17:29 pm »
Assuming you completed the repairs on the FT-100, I have 2 units, 1 won't transmit on HF, the other only puts out about 10 watts on HF.
Would you consider looking at these, as I'm more suited as an end-user.
I have been using these radios for a decade or more and have got quite used to pushing buttons and turning dials while driving therefore I have over a hundred DX contacts through this radio and would prefer getting them fixed instead of changing to a different model.
 
The following users thanked this post: mrz80

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #22 on: October 19, 2018, 10:08:28 pm »
I will answer you in your PM.
I told my friends I could teach them to be funny, but they all just laughed at me.
 

Offline m3vuv

  • Super Contributor
  • ***
  • !
  • Posts: 1738
  • Country: gb
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #23 on: October 20, 2018, 10:41:07 pm »
I realy dont know why people buy yaesu stuff,in my opinion its underbuilt over rated junk!!,every thing designed by bean counters not engineers,ive had a few yaesu radios before i knew any better!!.
 

Offline Wirehead

  • Regular Contributor
  • *
  • Posts: 178
  • Country: be
    • Wirehead.be
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #24 on: October 25, 2018, 06:42:46 am »
I realy dont know why people buy yaesu stuff,in my opinion its underbuilt over rated junk!!,every thing designed by bean counters not engineers,ive had a few yaesu radios before i knew any better!!.

A few bad apples.. just like any other brand  :palm: I have a FT-450AT; and modified it with a RX out for SDR purposes (HupRF high impedance buffer). Built like a tank. I can run 100W CW with a brick on the key for hours. Built like a tank.
"to remain static is to lose ground"
 

Offline mrz80

  • Contributor
  • Posts: 15
  • Country: us
  • The carpet is plush!
    • The Scotsman's Site of Web
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #25 on: December 01, 2018, 07:41:48 pm »
I realy dont know why people buy yaesu stuff,in my opinion its underbuilt over rated junk!!,every thing designed by bean counters not engineers,ive had a few yaesu radios before i knew any better!!.

My FT-100's been giving stalwart service for many years, most of 'em mobile and portable, getting banged around and overheated. I will concede it's a right pain in the rear to work on, with everything jammed in cheek-to-jowl in such a tiny case. So long as you baby that unobtanium VHF final (I don't run 2m or 440 at more than half output just to keep it running cool) it's a fine rig.  My big like is the 6m and VHF receivers are worlds ahead of the newer 857/897, and the Icom 706-of-whatever-generation.

A few bad apples.. just like any other brand  :palm: I have a FT-450AT; and modified it with a RX out for SDR purposes (HupRF high impedance buffer). Built like a tank. I can run 100W CW with a brick on the key for hours. Built like a tank.

Just remember to use a dummy load instead of an antenna for that torture test, or you might get a nastygram from th' FCC!  :-DD
Networks, Les Pauls, Telecasters, ham radio (WA4UF), bicycles, trains
 

Offline gi4ohh

  • Newbie
  • Posts: 5
  • Country: gb
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #26 on: February 23, 2019, 05:07:20 pm »
x-runner can you pm me please
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #27 on: February 23, 2019, 10:47:18 pm »
x-runner can you pm me please

I have PMed gi4ohh and he asked me to point to the resistors on the board. I told him to go back to this thread so I can post the pics here so that it may help other people in the future.

I will make the post in a bit ...  :popcorn:

I told my friends I could teach them to be funny, but they all just laughed at me.
 

Offline gi4ohh

  • Newbie
  • Posts: 5
  • Country: gb
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #28 on: February 23, 2019, 11:12:13 pm »
thanks
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #29 on: February 23, 2019, 11:48:58 pm »
Check the schematic and the annotated circuit board, that will show you the resistors to be replaced.

Good Luck!
I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: gi4ohh

Offline gi4ohh

  • Newbie
  • Posts: 5
  • Country: gb
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #30 on: February 24, 2019, 12:00:16 am »
the 5.6k resisters
my readings are as follows
5.6k
5.4k
4.28k
4.36k

the6.8k resisters
my readings are as follows
4.18k
5.16k
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #31 on: February 24, 2019, 02:17:08 pm »
Remember that measuring resistors in-circuit might not give the value on the resistor because it might be in parallel with other resistances. For example R3040 is essentially in parallel with R3035 & R3033 (and perhaps other things in other places not shown) as far as measuring it's resistance in-circuit. If you are concerned that the radio has the same problem as the one I repaired, I would just replace all of these resistors because it's not hard and the cost is so little.
I told my friends I could teach them to be funny, but they all just laughed at me.
 

Offline Velund

  • Regular Contributor
  • *
  • Posts: 74
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #32 on: February 27, 2019, 09:32:40 pm »
I have a FT-450AT; and modified it with a RX out for SDR purposes (HupRF high impedance buffer). Built like a tank. I can run 100W CW with a brick on the key for hours.

Cannot say anything bad about cooling of FT-450, but once tried to use my 450AT in a contest (RDXC, IIRC). After hearing for the first CW pileup replaced them with my old good FT-900CAT, without that buggy DSP, that cannot handle more than 2-3 CW signals in a passband.  What was a nice pileup on FT-900 appear to be a meaningless chaotic beeping on 450... BTW - no such problems on Elecraft K3.
 

Offline gi4ohh

  • Newbie
  • Posts: 5
  • Country: gb
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #33 on: March 14, 2019, 10:56:51 pm »
replaced resisters now full 100 watts on  hf
but on vhf uhf 1.5 watts only :(
 

Offline gi4ohh

  • Newbie
  • Posts: 5
  • Country: gb
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #34 on: March 17, 2019, 01:15:10 pm »
SUPPOSE THE CHANCES OF GETTING A MOTOROLA SRF 7043 MOSSFET ARE  SLIM
HAS ANYONE TRIED A REPLACEMENT OR EQUIVALENT WOULD LIKE TO GET THIS RADIO GOING ALSO ON 2 METERS AND 70CMS
 

Offline keystone

  • Contributor
  • Posts: 35
  • Country: us
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #35 on: March 21, 2019, 04:33:03 pm »
Hi xrunner.  I am putting together a test bench and looking for attenuators.  Was wondering where you got that one.  I'm working on an old kenwood tr-7800 fm 2 meter radio that has a problem with the squelch circuit, no squelch.  I've looked at your post of the tr-740o repair.  Thanks for posting that and this one too.  Have you ever run into a no squelch problem with a radio like this before?  Keep up the good work.
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #36 on: March 22, 2019, 01:20:57 am »
Hi xrunner.  I am putting together a test bench and looking for attenuators.  Was wondering where you got that one. 

The 40 dB? Oh I got it from a Chinese supplier on Ebay. You can find others used too that came out of commercial equipment.

Quote
I'm working on an old kenwood tr-7800 fm 2 meter radio that has a problem with the squelch circuit, no squelch.  I've looked at your post of the tr-740o repair.  Thanks for posting that and this one too.  Have you ever run into a no squelch problem with a radio like this before?  Keep up the good work.

Well I don't have the radio anymore because I repaired it for a friend, and have never touched one either before or since. You'll just have to do the troubleshooting on the bench and follow the schematic. I'm sure you can fix that.

As far as what you asked me in the PM, concerning what test equipment to get, let's talk about it here since there are other members that can input suggestions too. You said you got a DS1045Z. That's great. Some of the items on my bench include -

HP RF signal generator 100 kHz to 1 GHz
100W dummy load
Rigol DS1045Z
Rigol 30 MHz function generator
Rigol Bench DMM
Rigol DS815 Spec. Analyzer w/tracking generator
13.8V 30A power supply for testing ham gear
Two hp power supplies for low current applications
Other selections of various inline attenuators with both SMA and N connectors
Also a whole lot of other test equipment on the side but the above will do a lot of good for you.


I told my friends I could teach them to be funny, but they all just laughed at me.
 
The following users thanked this post: keystone

Offline N4wy

  • Newbie
  • Posts: 1
  • Country: us
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #37 on: April 03, 2019, 12:54:42 pm »
Hello Xrunner,  I have been searching for a replacement control board for the FT-100 for two years now.  Either Ebay has a board listed for the price of a used FT-100 $300+ or nobody has one.  This surprises me as many FT-100's are sitting around with problems.  You'd think someone would be piecing them out for parts.  Have you run across another source other than ebay for FT-100 parts or FT-100 for sale - not working for parts?  Thanks.  N4WY
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #38 on: April 04, 2019, 01:48:16 am »
You'd think someone would be piecing them out for parts.  Have you run across another source other than ebay for FT-100 parts or FT-100 for sale - not working for parts?  Thanks.  N4WY

Hello.

No, I'm afraid I don't know of other sources for parts. Keep looking on Ebay they're bound to turn up over time.  :-+
I told my friends I could teach them to be funny, but they all just laughed at me.
 

Offline F4IUJ

  • Newbie
  • Posts: 8
  • Country: fr
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #39 on: February 13, 2023, 03:07:16 pm »
Hello,

I have exactly the same issue, so I am going to replace the SMD resistors. So, do you know what size they are so that I can order them before dismantling the transceiver ?

73,

Yannig
 

Online xrunnerTopic starter

  • Super Contributor
  • ***
  • Posts: 7638
  • Country: us
  • hp>Agilent>Keysight>???
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #40 on: February 13, 2023, 03:33:42 pm »
Hello,

I have exactly the same issue, so I am going to replace the SMD resistors. So, do you know what size they are so that I can order them before dismantling the transceiver ?

73,

Yannig

One of my posts earlier noted that they were 0805 size.
I told my friends I could teach them to be funny, but they all just laughed at me.
 

Offline F4IUJ

  • Newbie
  • Posts: 8
  • Country: fr
Re: Repair of a Yaesu FT100 HF/VHF/UHF Transceiver
« Reply #41 on: February 13, 2023, 04:09:19 pm »
Ooops,

Sorry, I need some better glasses!!!

Anyway, thank you for making this info public, I don't think that I would have diagnose the issue alone.
 
The following users thanked this post: xrunner


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf