$20 LCR ESR Transistor checker project

[Azure]

Where can I buy such socket for ZIF socket?

You can buy quality ones form element14 and other brand name suppliers, otherwise you can get cheap ones from ebay.  Just search for "ZIF socket".

For a socket for the ZIF, same suppliers just search for "DIL socket".  You can just buy a normal socket the same size to use as the socket for the ZIF, or use 0.1" pin strips.  Be careful about using machines sockets as some ZIF pins do not fit into them.

[vinceroger]

Whats people thoughts on these testers
https://www.ebay.co.uk/itm/Transistor-Tester-TFT-Diode-Triode-Capacitance-Meter-LCR-TC1-ESR-NPN-PNP-MOSFET/123243495651?_trkparms=aid%3D222007%26algo%3DSIM.MBE%26ao%3D2%26asc%3D52945%26meid%3Ddc158dbd5ed6422f97eeabca7510c15f%26pid%3D100005%26rk%3D6%26rkt%3D12%26sd%3D222991613357%26itm%3D123243495651&_trksid=p2047675.c100005.m1851

[madires]

One major drawback of the TC1 is the additional MCU which controls power and the test button. That design is incompatible with the standard one and prevents firmware upgrades (k/m firmware). A while ago I released a simple circuit for replacing the control MCU to remove the incompatibility. Of course this will render the TC1's modified firmware useless. There could be another big problem with the design of power supply which I still have to investigate. My TC1's Vcc jumps around wildly, especially when it runs longer than a few seconds. Also the boost converter gets hot. Could be a bad component or bad design. The current draw seems a tad low compared to values others have reported. A common issue with the TC1 is a shorted cap in the power supply circuitry (backlight lit, but no display).

[vinceroger]

thanks for the reply it just seemed a good price now i know why.

[vinceroger]

is the t7 any better?
https://www.ebay.co.uk/itm/UK-Universal-LCR-T7-ESR-Diode-Triode-Capacitance-Mos-Transistor-Tester-CASE/123288444717?hash=item1cb4905f2d%3Ag%3AdEsAAOSw8lhbZAU7&_sacat=0&_nkw=LCR+T7&_from=R40&rt=nc&_trksid=m570.l1313

[Azure]

is the t7 any better?

Others may have more info, but I think it is basically the same inside as the LCR TC1.

[madires]

Yep, it's the same PCB with a different display module (dual row pin header at the right).

EDIT:
Update on my TC1's power supply issue. The problem was caused by the MLCC filter caps of the Zener test voltage. They were partly leaky and at some temperature they became even more leaky causing Vcc dips. It seems that C11 & C12 should be replaced with 0805 X7R 4.7µF 50V types from a reputable vendor anyway (haven't seen 100V for this type).

[bitseeker]

Hmm, I wonder if those MLCC were fractured inside.

[indman]

It seems that C11 & C12 should be replaced with 0805 X7R 4.7µF 50V types from a reputable vendor anyway (haven't seen 100V for this type).

Madires, http://www.farnell.com/datasheets/608985.pdf   ?

[madires]

Digikey's parametric search lists 0805 4.7µF MLCCs just up to 50V. And because the boost converter runs at 1MHz I'd prefer MLCCs over low-ESR TH electrolytics which are available for much higher voltages.

[stj]

the originals may only be rated at 25v or less, they may have used the same series they would for general logic.

[texaspyro]

An 0805 50V 4.7uF cap will probably have around 0.1uF capacitance at 50V...

[LatropEmit]

Hey everyone
I need some help with my tester. I tried to update the firmware with the mega644_LCD2004 k-firmware, but now when I try to power on the tester the LCD came on showing nothing and when I release the rotary it power of instantly.
I tried to read and search here and I know I have seen the answer somewhere but I can't remember where..

So my tester is the new one mentioned a few post ahead the Hiland M644.
I attached pictures from the display and the platine itself maybe it is easier to help with this pictures.

First I tried to flash the precopiled hex and eep then I tried to recompile it from scratch and setting in the make file some options like the right Part-No ect.
But I don't know what I have to set for the LCD.
To be honest I even don't  know if it's the right firmware to flash.. XD

Then setting the right fuses it's a other thing...
I tried with L 0xFF, H 0xD9 and E 0xFC then i tried with L 0x62, H 0xD9 and E 0xFC

But like you see not working, so now I am here to ask help

Ah if it helps originally it was a 1.12k fw on it..

Gesendet von meinem SM-G935F mit Tapatalk

[indman]

Digikey's parametric search lists 0805 4.7µF MLCCs just up to 50V. And because the boost converter runs at 1MHz I'd prefer MLCCs over low-ESR TH electrolytics which are available for much higher voltages.

AVX 4.7μF Multilayer Ceramic Capacitor MLCC 100V dc ±20% X7S Dielectric 1206 (3216M) SMD, Max. Temp. +125°C
I think that this model of the capacitor without problems will be suitable for replacement of C11-C12.
The place on the printed circuit board allows to make it.

Ah if it helps originally it was a 1.12k fw on it..

Did you try to read this original firmware (1.12k) or it is blocked for reading?
It is necessary to make the drawing of the schematic diagram in order that it is easier to understand as the display is connected to the ATMega644 processor!

[madires]

An 0805 50V 4.7uF cap will probably have around 0.1uF capacitance at 50V...

Yep, the DC bias derating. So it's a low-ESR electrolytic again.

[LatropEmit]

Yeah I had read the fw and I think I had it dumped properly but I got it overwritten afterwards... I thought I saved the fw in a secure place but in my rush I forgot do to so

Hmm... ok shame on me, when I let everything hooked up on my breadboard then i get this problem with the LCD shutting down after releasing ^^

If I try to power on the tester when everything is disconnected it powers on remains on but display is showing nothing..

I attached another picture with the back site of the pcb. First thing that I notice is that LCD and SPI are sharing some pins...

Ok found out display is a JLX12864G-378 V2.0 
Now I have to find out how configuring the make file...



Gesendet von meinem SM-G935F mit Tapatalk

[indman]

Ok found out display is a JLX12864G-378 V2.0
Now I have to find out how configuring the make file...

In the photo it isn't really well visible to what ports of the processor the display is connected! Can you make such table of connection of LCD to ATMega644 ports?
For example:
LCD (D6) - pin ATMega644?
LCD (D7) - pin ATMega644?
LCD (CS) - ?
LCD (RST) - pin ATMega644?
LCD (RS) -  pin ATMega644?

[LatropEmit]

Ok so I tried to trace back everything but i have some problems with VSS and CS they are connected to GND and maybe PA3...
I made a photos from the front and back site of the board. Then I overlapped both and tried to trace back..

So in sostans I have found

LCD        ATMEGA644

LEDA  -   VCC
VSS     -   GND (PA3)
VDD    -   VCC
RS      -    PB5
RST    -    RESET
CS      -    GND(PA3)
D7      -    PB7
D6     -     PB6

Like I said I have problems with VSS and CS but I attached the picture that I made with the trace lines. Black lines are on the backside of the pcb blue on the front hope I got I right ^^

Gesendet von meinem SM-G935F mit Tapatalk

[Discotech]

How low can the GM328 version read caps ?

Trying to measure some 3pF ceramic caps and it doesn't recognise them 

[madires]

k-firmware: 25pF
m-firmware: 5pF

solution:
- take a cap with a known value, e.g. 33pF, and connect it in parallel with the cap to check
- subtract capacitance of known cap

The "Sampling ADC" of the k-firmware might also work.

[Discotech]

k-firmware: 25pF
m-firmware: 5pF

solution:
- take a cap with a known value, e.g. 33pF, and connect it in parallel with the cap to check
- subtract capacitance of known cap

The "Sampling ADC" of the k-firmware might also work.

I've found another solution of putting in a higher rated cap it can detect, removing it so cap value resets to 0 then place small cap and it will show value

Seems strange it can detect value but only if test is already active ?

[indman]

LCD        ATMEGA644
LEDA  -   VCC
VSS     -   GND (PA3)
VDD    -   VCC
RS      -    PB5
RST    -    RESET
CS      -    GND(PA3)
D7      -    PB7
D6     -     PB6

The schematic of this clone almost completely corresponds to the schematic diagram from a manual of Karl-Heinz Kübbeler (March 8, 2018) on page 33 (figure 2.26) except for some details and the used display on ST7565.
Load a test firmware which I have collected. Everything has to work normally. I have checked this firmware in Proteus.
Fuse establish such LOW-F7, HIGH-D9, EXT-FC

[madires]

Actually that would be a bug. Hmm. There's another possibility. If the capacitance zero offset (determined during the self-adjustment) is larger than 25pF (k-firmware) it should also work. In this case the tester's own capacitance is large enough to work as a known cap in parallel.

[indman]

I've found another solution of putting in a higher rated cap it can detect, removing it so cap value resets to 0 then place small cap and it will show value
Seems strange it can detect value but only if test is already active ?

It is feature of work of k-firmware in the cycle mode.For the test of "small" capacities at first on test pins 1-3 in the mode of a cycle we measure any capacity above 25pf, then without pressing the Test button we connect on the same pins "small" value capacitor from 1pf.

[LatropEmit]

LCD        ATMEGA644
LEDA  -   VCC
VSS     -   GND (PA3)
VDD    -   VCC
RS      -    PB5
RST    -    RESET
CS      -    GND(PA3)
D7      -    PB7
D6     -     PB6

The schematic of this clone almost completely corresponds to the schematic diagram from a manual of Karl-Heinz Kübbeler (March 8, 2018) on page 33 (figure 2.26) except for some details and the used display on ST7565.
Load a test firmware which I have collected. Everything has to work normally. I have checked this firmware in Proteus.
Fuse establish such LOW-F7, HIGH-D9, EXT-FC

Soooo after checking the pins and re read the make file, and checked the config.h to see what pins are used, I realised that I have made a really big mistake....   
I didn't know what LCD controller to use in the make file..
Like I wrote it is a ST7565  so stupid me had in the make file WITH_LCD_ST7565 = 1306 AND NOT 1...
Therefore i compiled everything with the wrong settings...
Now after a quick test i got everything up and running... adjusting h-flip and now it's running without problems...

So in substance It works like a charme no extra fancy rewrite only setting everything right in the make file....

But thank you for taking the time to helping me

Gesendet von meinem SM-G935F mit Tapatalk