| Products > Test Equipment |
| Agilent/Keysight DS0-X 3014 error booting infiniivision.lnk |
| (1/2) > >> |
| elemenoh:
I have two DSO-X-3014A's that weren't booting, presumably due to corrupt flash memory. One successfully recovered, so my USB drive should be fine. The other scope is able to receive the nk.nb0 file, but when it begins to boot it hits the error below. The same issue occurs whether the USB stick is plugged into either front or rear port. IIRC I built the nk.nb0 and drive with firmware 02.35 (which I later updated to 02.66 on the scope that recovered). What should I try next? --- Code: ---running \Secure\Startup\infiniivision.lnk... System.MissingMethodException: Can't find an Entry Point 'RegisterNativeCompactLicensingCallbacks' in a PInvoke DLL 'Agilent.Cdf.Api.U. at Agilent.Cdf.Api.Licensing.Compact.LicenseSupervisor.g.a.c() at Agilent.Cdf.Api.NativeInterop.RegisterNativeCallbacks() at Agilent.InfiniiVision.infiniiVisionLauncher.Main(String[] args) --- End code --- |
| elemenoh:
For the heck of it I tried setting up everything with firmware 02.66 though I maybe read somewhere that version isn't bootable via USB? Anyway I gave it a shot but it hung at this point and eventually rebooted but failed in the normal corrupt flashy way. --- Code: ---Running infiniiVisionInstallHelper Failed to start/configure network. Device load time: NANDFLASH: 0 ms SNANDFLASH: 0 ms USB Hard Disk Drive: 0 ms ERROR: OALIoCtlHalGetDeviceInfo: Device doesn't support IOCTL_HAL_GET_DEVICE_INFO::SPI_GETBOOTMENAME --- End code --- |
| TheSteve:
The recovery drive generally needs to be built with the same version(or very close) that is corrupted on the scope. For the one you can't recover try some older versions. |
| elemenoh:
So far I've tried 02.65, 02.35, 02.20, 02.10 and 01.10 Versions older than 02.35 just hang indefinitely at --- Code: ---ProcessStartupFolder: \usb\Startup\ running \usb\Startup\infiniivision.lnk... --- End code --- Here's the spew from U-Boot from the corrupt flash. Does it give an indication of which firmware version would be needed to restore it @TheSteve? --- Code: ---U-Boot 2010.03 (Jan 26 2011 - 12:37:34)Agilent P500 CPU: SPEAr600 DRAM: 128 MiB Flash: 512 KiB NAND: 128 MiB In: serial Out: serial Err: serial SerNum:serial number not programmed Chip: BD Board Rev: 4 Net: smsc Press space to stop autoboot: 0 ## Booting kernel from Legacy Image at f8050000 ... Image Name: PBOOT Created: 2011-01-27 11:38:14 UTC Image Type: ARM Linux Kernel Image (gzip compressed) Data Size: 36703 Bytes = 35.8 KiB Load Address: 00000000 Entry Point: 00000000 Uncompressing Kernel Image ... OK Starting kernel ... Debug serial initialized ........OK Microsoft Windows CE Bootloader Common Library Version 1.4 Built Jan 27 2011 02:04:15 Microsoft Windows CE 6.0 Ethernet Bootloader for the Agilent P500 board Adaptation performed by Agilent Technologies (c) 2008 --- End code --- |
| elemenoh:
I'm a dummy and just realized the older versions I setup had the wrong data in infiniivision.lnk. Trying again with those. |
| Navigation |
| Message Index |
| Next page |