Products > Test Equipment

LaPOD: Low cost Logic Analyzer probe for MSO5k, DHO900 and more!

<< < (27/32) > >>

ebastler:

--- Quote from: S. Petrukhin on January 26, 2024, 10:31:51 am ---Maybe you have little experience and do not yet know the traditions and respectful attitude - I don't know.
But demonstrating this and showing lack of culture is not the best option.

--- End quote ---

Come on, man. Oliv3r and I have been around here longer than you. Why would you think you are entitled to teach us about forum traditions and culture?

On a loosely related note: Maybe you should reconsider your choice of forum avatar. I know it's just a picture -- but being lectured by a deranged-looking little guy who is waving his arms at me like an ape does in fact irritate me, and taints the reception of your posts. ::)

S. Petrukhin:

--- Quote from: ebastler on January 26, 2024, 10:43:41 am ---Come on, man. Oliv3r and I have been around here longer than you. Why would you think you are entitled to teach us about forum traditions and culture?

--- End quote ---
I'm sorry, I have no desire to talk about nonsense and respond to conclusions about the number of messages.  :-DD
Obviously, this is not the only forum where my posts are. It's weird...  :-//

S. Petrukhin:

--- Quote from: oliv3r on January 26, 2024, 10:39:05 am ---We still need a 9xxx breakout board, which requires a pinout :)

--- End quote ---
The author of the topic on this forum does not have the ability to delete messages, no additional permissions.  :-//
If there was such an opportunity, I would not delete - it is bad and insulting for users. 

Moderators may not interfere here, providing the maximum possible freedom.  :=\

I would suggest that you, nevertheless, create a new topic and insert a link to the beginning of the discussion in this topic in the first message.
It's a common case of "we moved from here: <message link>".  :popcorn:

oliv3r:
We could start fighting here, so that dave comes in and splits the thread :)

BTW, you can edit the subject of the first message in a thread, which is also the thread topic :)

Or, we can just ignore all the bickering and focus on the part discussion at hand. So feel free to do some reviewing of the schematics/pcb/bom :D

Once I've got a 'v1.0' and we don't have a split thread, I surely will create a new thread, as the history is less relevant then.

oliv3r:
I just did a Paper print, just to see how it would fit int he scope. Depending on how much room the case would consume on the sides, the second output is 'close' but not too close. I think there's about a cm between the bnc connector (with the plastic cap on) and the paper edge of the PCB.

As for the HDMi connectors, The cheap ones I got 50 cm with quite fat shrouds around the connector, leave about 1.5mm (bare eye measurement) of space between each connector. I don't really want to get them closer together then that, which means, I won't have more space around the edges either to narrow the footprint. Of course this isn't a problem for the mini-hdmi variant :)

I'lll leave the DSO7000 and DS1074Z out for the time being, as I don't think we have a verified pinout for either? (Though the DS1074Z might be available already? idk. Doing the pcb design is easy, but I don't have either so ...

I'll let this linger for a bit for people to look at. I've attached the pdf's of the boards, which probably makes for easier review.

Oh, the pipelines are 'done' in that I would be able tag and release the designs and get permanent outputs. I'll merge and tag the results next week, just after the artifacts expire. I won't be sending the gerbers of to the fab just yet, as I need to finish a few other boards too, but I'll start that new thread next week that people are so anxious about :p

Anyways, have a good weekend already :)

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod