Author Topic: Brymen BM869(867) alternative software.  (Read 29018 times)

0 Members and 1 Guest are viewing this topic.

Offline coromonadalix

  • Super Contributor
  • ***
  • Posts: 3316
  • Country: ca
Re: Brymen BM869(867) alternative software.
« Reply #75 on: August 05, 2018, 05:20:43 pm »
very good work

thks Sairus for creating this piece of software,   i would love to have one ported for the Fluke 189 series, to replace the Fluke View software, and i would give some $$ to support the creator
 

Offline t1d

  • Frequent Contributor
  • **
  • Posts: 843
  • Country: us
Re: Brymen BM869(867) alternative software.
« Reply #76 on: September 18, 2018, 10:59:04 am »
Thank you, so much, Sairus, for your hard work, time, talent and graciousness, in sharing your Brymen program. I think I missed this post, back when we were working on the original "sniffing" thread... Doh! I have downloaded the file and look forward to trying it out.
 

Offline spidola

  • Contributor
  • Posts: 20
  • Country: ua
Re: Brymen BM869(867) alternative software.
« Reply #77 on: September 19, 2018, 08:04:44 pm »
Thank you Sairus  :)
 

Offline Stefan3v

  • Newbie
  • Posts: 2
  • Country: ro
Re: Brymen BM869(867) alternative software.
« Reply #78 on: March 17, 2019, 11:32:25 am »
Sairus this project is a joke? Because is not funny!
I tried version Sairus DMM 1.04 with Arduino LEONARDO and it does not work. Pullup resistors for IR receiver: 5K, 10K, 20K, 30K, 40K, 50K, 60K, 100K, 150K.

Option "Port debug line" not work in version 1.04.  |O

 

Offline Sairus

  • Contributor
  • Posts: 38
  • Country: by
Re: Brymen BM869(867) alternative software.
« Reply #79 on: March 19, 2019, 11:01:13 am »
I checked software using virtual port pair and port debug line work fine. It show data after receiving and clear line after some time to indicate port activity. If after enabling function you dont se anything it mean that there no data coming to the port.

So do you select right port and settings set?
Do you connect to it without errors?
Error message (no signal) aper on display?

Arduino sketch was tested on UNO model, first i recommend send random data to serial port to check software and windows serial driver on you PC.

Best regards Sairus.
 

Offline Stefan3v

  • Newbie
  • Posts: 2
  • Country: ro
Re: Brymen BM869(867) alternative software.
« Reply #80 on: March 20, 2019, 08:15:19 pm »
Thanks Sairus and sorry for blaming you. Sairus DMM 1.04 is OK with Arduino UNO.
The serial port connected to the LEONARDO USB uses CDC (communications device class) to simulate UART functionality.

Many thanks!
 

Offline Giox040

  • Contributor
  • Posts: 9
  • Country: it
Re: Brymen BM869(867) alternative software.
« Reply #81 on: June 17, 2021, 04:46:38 pm »
Hi Sairus!
Your software is really interesting and I Thank You for making it available.

I'm fine-tuning the interface I've built around an Attiny85for my new BM869S, in case you are planning some upgrade, please consider the enlargement of the "Time" column of the login; in my PC I can see the date, hours and minutes but the seconds are truncated (even more than in the image of the previous post).

Furthermore, it would be convenient for the configuration parameters to be saved on file, instead of inserting them each time the program is started.

Thanks a lot!
 

Offline radiolistener

  • Super Contributor
  • ***
  • Posts: 1819
  • Country: ua
Re: Brymen BM869(867) alternative software.
« Reply #82 on: June 18, 2021, 10:39:56 pm »
This is a technical forum. Downloading source code is no different than downloading a circuit schematic, PCB layout or B.O.M.

I would hesitate to run a downloaded executable however it was delivered.

you're right it's not safe to run executables from unknown source. But there is down side of the coin. The author may not want to share some algorithm details, but can share executable which use it. For example, sometimes I don't want to share some signal processing code with my optimizations for which I spend a lot of time. I can share executable with obfuscation, but obfuscation leads to a false positive on antiviruses. So I decided not share these projects at all.

At a glance it looks that this is doesn't have sense. But in reality things are not so easy. Sometimes when you share some project as open source and it has good commercial perspective, you can catch some bad things. For example, you will find some peoples who use your code for commercial purposes and then they start to insulting you and will try to kick off your open source projects from the market.

I don't see the commercial perspective for this software, but this is the right of author to decide if he want to share source code or not.
 

Online Fungus

  • Super Contributor
  • ***
  • Posts: 12360
  • Country: 00
Re: Brymen BM869(867) alternative software.
« Reply #83 on: June 19, 2021, 08:16:07 am »
This is a technical forum. Downloading source code is no different than downloading a circuit schematic, PCB layout or B.O.M.

I would hesitate to run a downloaded executable however it was delivered.

Source code can contain malware, too.

(If you think about it: That bad exe file has source code!)
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf