Products > Test Equipment
FeelTech FY6600 60MHz 2-Ch VCO Function Arbitrary Waveform Signal Generator
<< < (383/450) > >>
beanflying:
For those suffering with blown or broken units this may offer a possible way out FINALLY after some kicking :palm: Taken from the spriuking 6900 thread in the For Sale section.

Personally I think their way out should be firmware release but this may at least provide an option better than has been available in the past.


--- Quote from: feeltech on July 25, 2019, 03:57:00 am ---
--- Quote from: feeltech on July 24, 2019, 11:07:22 am ---You simply FAIL to comprehend your past. About the only way forward to start to remedy this is release the firmware for the FY6600 and the method to repair damaged units. Either that or consider sending 'review samples of your new one to those affected that have dead units. Return shipping and freighting units is just not on unless YOU are paying for postage both ways.

Both of the member quotes above were from your most recent spruiking of the 6800. And surprise surprise went unanswered.
This Link https://www.eevblog.com/forum/contests/feeltech-fy6800-signal-generator-free-trial/

--- End quote ---

We have no staff to take charge of this forum account before. We have not landed in this forum for a long time. We apologize for the vacancy in our work. At the same time, we will compensate the damaged customers. From now on, our account is in the charge of a special person, we will maintain the forum. Customers who have purchased version FY6600 V3.0 before will send the firmware chip downloaded version V3.1 free of charge as long as they contact us. At the same time, if these customers intend to purchase FY6900 series products, our company will return all the profits of the machine to customers, charging only the cost of equipment and transportation costs. Please contact us in EVVblog or Email.

Email address: service@feelelec.com

--- End quote ---
bitseeker:
Interesting development. Of course, the proof in the pudding is in the eating. So, it's time for all the V3 owners to put FE to the test.
beanflying:

--- Quote from: bitseeker on July 25, 2019, 05:15:13 am ---Interesting development. Of course, the proof in the pudding is in the eating. So, it's time for all the V3 owners to put FE to the test.

--- End quote ---

I dropped Fremen67 a PM. Offhand I can't recall others with dead or partially dead units but if others do hit them up.
FeelElec:

--- Quote from: battlecoder on July 14, 2019, 12:34:50 am ---Has anyone gotten the firmware update to work with PC Software version 6.0?
My FY6600 has firmware 3.1, PC Software says that the latest available firmware is 3.3, but when I click "update" it seems to download something but then it immediately throws the error "USB linkage fault".

--- End quote ---

Dear Customers,
3.3 began to add online upgrade function, 3.1 does not support online upgrade.
If you have any problems with version 3.1, please feel free to contact us.

FeelElec
battlecoder:

--- Quote from: FeelElec on July 25, 2019, 07:27:36 am ---
--- Quote from: battlecoder on July 14, 2019, 12:34:50 am ---Has anyone gotten the firmware update to work with PC Software version 6.0?
My FY6600 has firmware 3.1, PC Software says that the latest available firmware is 3.3, but when I click "update" it seems to download something but then it immediately throws the error "USB linkage fault".

--- End quote ---

Dear Customers,
3.3 began to add online upgrade function, 3.1 does not support online upgrade.
If you have any problems with version 3.1, please feel free to contact us.

FeelElec


--- End quote ---

Oh. That's quite unfortunate.
Thanks for the answer, though.
Do you have a changelog of what was updated, changed, or fixed in version 3.3 so I can see what I'm missing?
Navigation
Message Index
Next page
Previous page
There was an error while thanking
Thanking...

Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod