Products > Test Equipment
REVIEW - Rigol DS2072 - First Impressions of the DS2000 series from Rigol
Corporate666:
--- Quote from: marmad on June 29, 2013, 11:07:15 am ---
--- Quote from: Corporate666 on June 29, 2013, 01:26:35 am ---Is it possible I have a later firmware and this keypress method to get the full version info has been removed?
--- End quote ---
If you still can't get the button method to work, install NI VISA runtime (you need it for RUU anyway) and Rigol Ultra Sigma software.
Connect DSO via USB; boot the DSO; start Ultra Sigma; open SCPI Control Panel; type (or copy and paste) the following:
:SYSTem:SETup?
You will see the full FW version number in the top line of the return data.
--- End quote ---
It's strange, I turned key beep off and still could not see the firmware screen. I must have tried it over 100 times being very deliberate and careful with button presses.
Well, I installed NI-Visa and RUU (great software, BTW!) and typed the command into the SCPI control panel. Result: 00.01.00.00.03.
marmad:
--- Quote from: Corporate666 on June 29, 2013, 05:22:51 pm ---It's strange, I turned key beep off and still could not see the firmware screen. I must have tried it over 100 times being very deliberate and careful with button presses.
Well, I installed NI-Visa and RUU (great software, BTW!) and typed the command into the SCPI control panel. Result: 00.01.00.00.03.
--- End quote ---
You were checking System -> System Info after each of those times, right? If so, it's very strange... I just did it with FW 01.00.00.03 first time without a problem.
Corporate666:
--- Quote from: marmad on June 29, 2013, 07:15:15 pm ---
--- Quote from: Corporate666 on June 29, 2013, 05:22:51 pm ---It's strange, I turned key beep off and still could not see the firmware screen. I must have tried it over 100 times being very deliberate and careful with button presses.
Well, I installed NI-Visa and RUU (great software, BTW!) and typed the command into the SCPI control panel. Result: 00.01.00.00.03.
--- End quote ---
You were checking System -> System Info after each of those times, right? If so, it's very strange... I just did it with FW 01.00.00.03 first time without a problem.
--- End quote ---
Figured it out.
I ran the key test, and while I had done that previously, this time when I pressed the '6' key, nothing happened. I had noticed the key felt a little different, so after some more testing it was not working - unless you really pushed it slowly, hard and deliberately. I pushed the key in really hard and wiggled it around a little, and now it's fine. It's almost like there was something on the board or the key was not accurately lined up in it's set. Now it works, and the key feels like the others!
And now I see the full system info on the screen.
alank2:
TE sent me a tracking number, I should get it Friday.
Wim13:
From the Rigol website:
http://beyondmeasure.rigoltech.com/acton/form/1579/0012:d-0001/1/index.htm
Firmware Update Request
Here are the latest Firmware versions by Rigol product family as of June 1, 2013:
DS2000 FW-Version: 00.01.00.00.03
DS4000 FW-Version: 00.01.00.00.07
DS6000 FW-Version: 00.01.04
DSA815 FW-Version: 00.01.06
DSA1000 FW-Version: 00.01.14
DG4000 FW-Version: 00.01.06
DG5000 FW-Version: 01.01.08
To request an upgrade please fill out the information below and we will contact you. Upgrade compatibility may depend on the serial number, hardware revisions and current firmware of your instrument. Not all instruments may be upgradable to the latest firmware.
You can also contact your local office or distributor for information or to discuss the benefits of a firmware update.
Rigol Technologies USA Applications:
www.rigoltech.com
Email: techsupport@rigol.com
Phone: 440-232-4488
Rigol Technologies EU GmbH:
Lindberghstraße 4
82178 Puchheim
+49 (0)89 - 8941895-0
sales-europe@rigoltech.com
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version