Products > Test Equipment

Hantek 6022BE 20MHz USB DSO

<< < (216/241) > >>

edovis:
I've been getting this issue too since windows decided to update itself. I'm running Windows 10 and PC keeps telling me that the driver for DRIVER1 is corrupted |O . I've already tried everything and couldn't get it to work again

Microcheap:
Hantek's USB drivers are a mess. Try to do this: Open the Windows Device Manager and mark the option "Show hidden devices" in "View" menu. Remove all Hantek drivers. Unplug an plug the device again to confirm that there is no driver left in the system. When you see only the yellow exclamation mark, download the latest drivers from Hantek and manually install the Win 10 driver (even if you are using Windows 7), apparently this is the newest driver and what worked better for me. I am using Win 10 but I tested it in a Win7 VM.

I don't have a 6022BL at hands now, but I quickly tested the Open6022BE PR19 with a 6022BE and couldn't reproduce the hanging problem, there is a lot of other bugs, but no hanging. It is a shame the developer stopped working on Open6022BE and nobody could took over the project, it is really promising and by far the best alternative to the official software. I wish I had the skills...
Anyway, I got the PR19 version from the link https://jumpshare.com/v/bviO41a4x8CiAaSSbama

MarkFalk:
I am not familiar with the open-source-stuff, so I would like to ask:
I have seen that the github-openhantek-project also has a Windows-Version:
https://github.com/OpenHantek/openhantek
This version seems to be for 64bit only. Isn´t there a 32bit-Version?

MarkFalk:

--- Quote from: RichardK on December 09, 2013, 04:40:41 pm ---
--- Quote ---I would be very interested in what you've done with the front end
--- End quote ---

I also stacked (in a very bodgy fashion) SMD capacitors on top of ALL the bypassing capacitors for the USB Micro and ADC.

Then I stacked SMD Capacitors on the larger of the three SMDs before the DC-DC (C103 & C105) and I stacked the SMD Capacitors on the other side, specifically the large ones going between +5 and -5 and the ones going from +5 to GND and -5 to GND, both before and after the Inductors.

--- End quote ---

Any recommendations reg. the values of the added SMD-caps?

MarkFalk:

--- Quote from: Fabio1963 on January 05, 2017, 11:03:13 am ---Hi
I've added the Lissajous figure to PCSCOPE (version 1.7)
See attached figure
Fabio

--- End quote ---

Yesterday I checked the last version of PCScope I found. I like it esp. the top "preview"-window. It runs also with 6022bl after replacing the  HTMarch.dll by the HTMarch.dll from BL´s SDK-package (after reading the reg. posts here I exspected that it also supports the 6022BL but it did not so). But there are some bug, maybe depending on using BL´s HTMarch.dll (I own a 6022BL, so I can not check this with a 6022BE):
- The top preview-Window only shows "events", waves, of channel 1.
- The vertikal position of the channels is not adjustable - sometimes it is good drawing them on the same baseline (zero), but sometimes the "traditional" appearance with left channel in the upper and right channel in the lower part od the screen is better.
- Changing the V/div-adjustment only works when both channels are set to the same value
- When changing the time of data aquiring ("recording") the timebase-adjustment is set to a low value (w/o a need)
- The software looses all adjustments (e.g. activated channel, probe x1/x10) when leaving/closing.

Regards, Mark

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod