| Products > Test Equipment |
| Hantek DSO1152S - Wont boot after firmware update |
| << < (14/26) > >> |
| tinhead:
emerg.do (and all the even newer recovery tricks) are implemented into dsod file. You remember, you renamed it to stop the boot loop. That file need to be there and loaded, and when the firmware is crashing (or not loaded or missing) the dsod will look for "magic" on flash drive. You can see the output/status mesages on uart. Btw., on my dev board when i follow the instruction the dsod is looking for system*.up and not doing what it should do :P So who knows what your handheld is doing (that depends on version of dsod) |
| WanaGo:
OK interesting stuff. They replied again when I said it didnt work. Here is what they said --- Quote ---Since you could use UART connection, please use attached "uart_update" to solve the problem. Steps as follows: 1. Just uncompress packet file. And store packet and do_update files to a USB drive, and plug the USB drive to DSO, turn on DSO. 2. Connect DSO to PC by UART. 3. And input following commands in the UART tool on PC. 1?cd /mnt/udisk/ 2) chmod +x /mnt/udisk/do_update 3) /mnt/udisk/do_update --- End quote --- and sent me the file I put here: http://www.taktik.co.nz/EEVBlog/uart_update.rar Have an excuse to open it back up now and take that photo for you under the shield covers. Will do that now Regards WanaGo |
| WanaGo:
Photos from under the cover are here. Also all scrubbed apart from the one near the opening. Sorry if they are not very clear http://www.taktik.co.nz/EEVBlog/DSO1152S-UnderCover.zip Regards WanaGo |
| WanaGo:
Followed their instructions... Even worse now... Display is now completely snow after the main start pages. Here is the log --- Quote ---[root@Hantek /]# cd /mnt/udisk [root@Hantek udisk]# chmod +x /mnt/udisk/do_update [root@Hantek udisk]# /mnt/udisk/do_update kernel is 2.6.30.4 ln: /lib/libgif.so.6: File exists rm: can't remove '/OurLanguages': Directory not empty mkdir: can't create directory '/OurLanguages': File exists save exit: isCheckpointed 0 umount: /dev/sda1 busy - remounted read-only umount: tmpfs busy - remounted read-only [root@Hantek udisk]# umount: can't remount /dev/root read-only umount: can't remount rootfs read-only The system is going down NOW! Sent SIGTERM to all processes s3c2410-wdt s3c2410-wdt: Unexpected close, not stopping watchdog Sent SIGKILL to all processes Requesting system reboot s3c2440-sdi s3c2440-sdi: powered down. Restarting system.ΓΏ*** Warning - bad CRC or NAND, using default environment ##### EmbedSky BIOS for SKY2440/TQ2440 ##### Press Space key to Download Mode ! Booting Linux ... Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kernel to SDRAM done,NOW, Booting Linux...... Uncompressing Linux... done, booting the kernel. Linux version 2.6.30.4 (root@zgt) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #125 Sat Jun 30 17:13:48 CST 2012 CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177 CPU: VIVT data cache, VIVT instruction cache Machine: TQ2440 ATAG_INITRD is deprecated; please update your bootloader. Memory policy: ECC disabled, Data cache writeback CPU S3C2440A (id 0x32440001) S3C24XX Clocks, (c) 2004 Simtec Electronics S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0 NR_IRQS:85 irq: clearing pending ext status 00000300 irq: clearing subpending status 00000002 PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [ttySAC0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61260KB available (3160K code, 346K data, 100K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop... 199.47 BogoMIPS (lpj=498688) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 296 bytes NET: Registered protocol family 16 S3C2440: Initialising architecture S3C2440: IRQ Support S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics DMA channel 0 at c4808000, irq 33 DMA channel 1 at c4808040, irq 34 DMA channel 2 at c4808080, irq 35 DMA channel 3 at c48080c0, irq 36 S3C244X: Clock Support, DVS off bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 yaffs Jun 30 2012 14:45:29 Installing. msgmni has been set to 119 alg: No test for stdrng (krng) io scheduler noop registered (default) backlight initialized s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440 s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440 s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440 loop: module loaded Driver 'sd' needs updating - please use bus_type methods S3C24XX NAND Driver, (c) 2004 Simtec Electronics s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x000000000000-0x000000040000 : "EmbedSky_Board_uboot" 0x000000200000-0x000000400000 : "EmbedSky_Board_kernel" 0x000000400000-0x000003ff8000 : "EmbedSky_Board_yaffs2" 0x000000100000-0x000000200000 : "EmbedSky_Board_logo" ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver s3c2410-ohci s3c2410-ohci: S3C24XX OHCI s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 pl2303: Prolific PL2303 USB to serial adaptor driver mice: PS/2 mouse device common for all mice S3C24XX RTC, (c) 2004,2006 Simtec Electronics s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0 Linux video capture interface: v2.00 S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics s3c2410-wdt s3c2410-wdt: starting watchdog timer s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled mapped channel 0 to 0 s3c2440-sdi s3c2440-sdi: powered down. s3c2440-sdi s3c2440-sdi: initialisation done. s3c2440-sdi s3c2440-sdi: powered down. usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.18a. No device for DAI UDA134X No device for DAI s3c24xx-i2s S3C24XX_UDA134X SoC Audio driver UDA134X SoC Audio Codec asoc: UDA134X <-> s3c24xx-i2s mapping ok ALSA device list: #0: S3C24XX_UDA134X (UDA134X) TCP cubic registered RPC: Registered udp transport module. RPC: Registered tcp transport module. lib80211: common routines for IEEE802.11 drivers s3c2410-rtc s3c2410-rtc: setting system clock to 2009-01-01 00:01:39 UTC (1230768099) yaffs: dev is 32505858 name is "mtdblock2" yaffs: passed flags "" yaffs: Attempting MTD mount on 31.2, "mtdblock2" usb 1-1: new full speed USB device using s3c2410-ohci and address 2 usb 1-1: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices yaffs_read_super: isCheckpointed 0 VFS: Mounted root (yaffs filesystem) on device 31:2. Freeing init memory: 100K insmod: can't insert '/lib/cfbcopyarea.ko': No such file or directory insmod: can't insert '/lib/cfbfillrect.ko': No such file or directory insmod: can't insert '/lib/cfbimgblt.ko': No such file or directory insmod: can't insert '/lib/s3c2410fb.ko': No such file or directory bwscon:0x2201d110 fpga bank 221422 dso-fpga: install ok dso-spi initialized Init spi success! New Log Write OK Length:21 s3c2440_clkcon=00FE7FF0 fpga download file_name :dn.rbf copy-from-user ok dn_file_name:dn.rbf fpga_down_load file name : dn.rbf. data DOWN finish. dso-spi:FPGA_DOWNLOAD ok. release <0>open LCD error: No such file or directory dm9000 Ethernet Driver, V1.31 Now use the default MAC address: 10:23:45:67:89:ab eth0 (dm9000): not using net_device_ops yet eth0: dm9000e at c487a300,c487e304 IRQ 53 MAC: 10:23:45:67:89:ab (EmbedSky) Try to bring eth0 interface up ... Hantek GPIO(buzzer/speaker),(c)20110309 Hantek-gpio initialized speaker on Beep dso-buzzer initialized insmod: can't insert '/dso/driver/usb-storage.ko': No such file or directory ifconfig eth0 hw ether 10:23:45:67:89:ab eth0: link down ifconfig eth0 192.168.1.55 netmask 255.255.255.0 up /sbin/net_set: line 5: route: not found add default gw 192.168.1.2 Done scsi 0:0:0:0: Direct-Access Lexar JumpDrive 1100 PQ: 0 ANSI: 0 CCS sd 0:0:0:0: [sda] 15679488 512-byte hardware sectors: (8.02 GB/7.47 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] Attached SCSI removable disk i2c /dev entries driver s3c2440-i2c s3c2440-i2c: slave address 0x10 pdata->frequency=6000 s3c2440-i2c s3c2440-i2c: bus frequency set to 9 KHz s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter s3c2410_udc: debugfs dir creation failed -19 s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes g_serial gadget: Gadget Serial v2.4 g_serial gadget: g_serial ready lcd_init dso-lcd1 initialized insmod: can't insert '/dso/driver/dso-adc.ko': No such file or directory tq2440_ts: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint TQ2440 TouchScreen successfully loaded input: TQ2440 TouchScreen as /devices/virtual/input/input0 Power-Ctrl initialized Please press Enter to activate this console. cannot open lcd : No such file or directory s3c2440_clkcon=00FFFFF0 MachineFunctionLimitByBrandType release save exit: isCheckpointed 0 umount: tmpfs busy - remounted read-only umount: tmpfs busy - remounted read-only The system is going down NOW! s3c2410-wdt s3c2410-wdt: Unexpected close, not stopping watchdog Sent SIGTERM to all processes Sent SIGKILL to all processes Requesting system reboot s3c2440-sdi s3c2440-sdi: powered down. *** Warning - bad CRC or NAND, using default environment ##### EmbedSky BIOS for SKY2440/TQ2440 ##### Press Space key to Download Mode ! Booting Linux ... Copy linux kernel from 0x00200000 to 0x30008000, size = 0x00200000 ... Copy Kernel to SDRAM done,NOW, Booting Linux...... Uncompressing Linux... done, booting the kernel. Linux version 2.6.30.4 (root@zgt) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-176) ) #125 Sat Jun 30 17:13:48 CST 2012 CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177 CPU: VIVT data cache, VIVT instruction cache Machine: TQ2440 ATAG_INITRD is deprecated; please update your bootloader. Memory policy: ECC disabled, Data cache writeback CPU S3C2440A (id 0x32440001) S3C24XX Clocks, (c) 2004 Simtec Electronics S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0 NR_IRQS:85 irq: clearing pending ext status 00000300 irq: clearing subpending status 00000002 PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [ttySAC0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61260KB available (3160K code, 346K data, 100K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop... 199.47 BogoMIPS (lpj=498688) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 296 bytes NET: Registered protocol family 16 S3C2440: Initialising architecture S3C2440: IRQ Support S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics DMA channel 0 at c4808000, irq 33 DMA channel 1 at c4808040, irq 34 DMA channel 2 at c4808080, irq 35 DMA channel 3 at c48080c0, irq 36 S3C244X: Clock Support, DVS off bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 yaffs Jun 30 2012 14:45:29 Installing. msgmni has been set to 119 alg: No test for stdrng (krng) io scheduler noop registered (default) backlight initialized s3c2440-uart.0: tq2440_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440 s3c2440-uart.1: tq2440_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440 s3c2440-uart.2: tq2440_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440 loop: module loaded Driver 'sd' needs updating - please use bus_type methods S3C24XX NAND Driver, (c) 2004 Simtec Electronics s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=3 30ns, Twrph1=2 20ns NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x000000000000-0x000000040000 : "EmbedSky_Board_uboot" 0x000000200000-0x000000400000 : "EmbedSky_Board_kernel" 0x000000400000-0x000003ff8000 : "EmbedSky_Board_yaffs2" 0x000000100000-0x000000200000 : "EmbedSky_Board_logo" ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver s3c2410-ohci s3c2410-ohci: S3C24XX OHCI s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 pl2303: Prolific PL2303 USB to serial adaptor driver mice: PS/2 mouse device common for all mice S3C24XX RTC, (c) 2004,2006 Simtec Electronics s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0 Linux video capture interface: v2.00 S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics s3c2410-wdt s3c2410-wdt: starting watchdog timer s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq enabled mapped channel 0 to 0 s3c2440-sdi s3c2440-sdi: powered down. s3c2440-sdi s3c2440-sdi: initialisation done. s3c2440-sdi s3c2440-sdi: powered down. usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.18a. No device for DAI UDA134X No device for DAI s3c24xx-i2s S3C24XX_UDA134X SoC Audio driver UDA134X SoC Audio Codec asoc: UDA134X <-> s3c24xx-i2s mapping ok ALSA device list: #0: S3C24XX_UDA134X (UDA134X) TCP cubic registered RPC: Registered udp transport module. RPC: Registered tcp transport module. lib80211: common routines for IEEE802.11 drivers s3c2410-rtc s3c2410-rtc: setting system clock to 2009-01-01 00:02:00 UTC (1230768120) yaffs: dev is 32505858 name is "mtdblock2" yaffs: passed flags "" yaffs: Attempting MTD mount on 31.2, "mtdblock2" usb 1-1: new full speed USB device using s3c2410-ohci and address 2 usb 1-1: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices yaffs_read_super: isCheckpointed 0 VFS: Mounted root (yaffs filesystem) on device 31:2. Freeing init memory: 100K insmod: can't insert '/lib/cfbcopyarea.ko': No such file or directory insmod: can't insert '/lib/cfbfillrect.ko': No such file or directory insmod: can't insert '/lib/cfbimgblt.ko': No such file or directory insmod: can't insert '/lib/s3c2410fb.ko': No such file or directory bwscon:0x2201d110 fpga bank 221422 dso-fpga: install ok dso-spi initialized Init spi success! New Log Write OK Length:21 s3c2440_clkcon=00FE7FF0 fpga download file_name :dn.rbf copy-from-user ok dn_file_name:dn.rbf fpga_down_load file name : dn.rbf. data DOWN finish. dso-spi:FPGA_DOWNLOAD ok. release <0>open LCD error: No such file or directory dm9000 Ethernet Driver, V1.31 Now use the default MAC address: 10:23:45:67:89:ab eth0 (dm9000): not using net_device_ops yet eth0: dm9000e at c487a300,c487e304 IRQ 53 MAC: 10:23:45:67:89:ab (EmbedSky) Try to bring eth0 interface up ... Hantek GPIO(buzzer/speaker),(c)20110309 Hantek-gpio initialized speaker on Beep dso-buzzer initialized ifconfig eth0 hw ether 10:23:45:67:89:ab insmod: can't insert '/dso/driver/usb-storage.ko': No such file or directory eth0: link down ifconfig eth0 192.168.1.55 netmask 255.255.255.0 up /sbin/net_set: line 5: route: not found add default gw 192.168.1.2 Done scsi 0:0:0:0: Direct-Access Lexar JumpDrive 1100 PQ: 0 ANSI: 0 CCS sd 0:0:0:0: [sda] 15679488 512-byte hardware sectors: (8.02 GB/7.47 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] Attached SCSI removable disk i2c /dev entries driver s3c2440-i2c s3c2440-i2c: slave address 0x10 pdata->frequency=6000 s3c2440-i2c s3c2440-i2c: bus frequency set to 9 KHz s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter s3c2410_udc: debugfs dir creation failed -19 s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes g_serial gadget: Gadget Serial v2.4 g_serial gadget: g_serial ready lcd_init dso-lcd1 initialized insmod: can't insert '/dso/driver/dso-adc.ko': No such file or directory tq2440_ts: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint TQ2440 TouchScreen successfully loaded input: TQ2440 TouchScreen as /devices/virtual/input/input0 Power-Ctrl initialized Please press Enter to activate this console. cannot open lcd : No such file or directory s3c2440_clkcon=00FFFFF0 MachineFunctionLimitByBrandType release rm: can't remove '/param/sav/run*': No such file or directory --- End quote --- |
| WanaGo:
Oh dear. |
| Navigation |
| Message Index |
| Next page |
| Previous page |