Products > Test Equipment
Hantek HDG2002B AWG: 5Mhz or 100MHz? Let's see!
fremen67:
--- Quote from: smgvbest on February 22, 2015, 07:22:55 am ---I just added the Network parts and the Hi Freq Parts to my Unit and have a couple of questions
after I got it back together I notice the lights do not come on on the RJ45 but I do see a MAC address now in the Network Setup
I would expect that to come on when plunging in a network cable yet it did not.
--- End quote ---
The green light should be on when the cable is connected. Do you have a message in the serial console when you plug a cable? Something like
--- Code: ---dm9000 dm9000: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
--- End code ---
and something like this when you unplug it:
--- Code: ---dm9000 dm9000: eth0: link down
--- End code ---
I would bet on a bad solder as the lan jack is powered by the DM9000AEP through the H1102NL magnetics. Do you have any pictures of both side of the lan area?
--- Quote from: smgvbest on February 22, 2015, 07:22:55 am --- Do I need to do an ifconfig to see that happen or is something probably wrong?
--- End quote ---
ifconfig is already called in /dso/etc/boot.sh:
--- Code: ---...
ifconfig eth0 192.168.1.127 up
#/etc/init.d/nfs.sh &
#telnetd &
...
--- End code ---
So your IP is already set. You will have to uncomment the telnet line to activate it and if you want to connect to a nfs server, you will also have to uncomment the nfs line and modify nfs.sh script.
--- Quote from: smgvbest on February 22, 2015, 07:22:55 am ---Next after adding the LMX5080 my Hi Freq counter works fine but not the low freq one where there any other changes needed when adding the LMX5080 that I missed?
--- End quote ---
Any picture of that area? I attached the one I took from this area. The components where already installed.
smgvbest:
@fremen67
Thankyou very much for posting the automation script for the calibration
Here's two images for the top and bottom of the counter
Here's the Top of the Counter
And the Bottom of the counter
I'll get the others here soon as I can
smgvbest:
@fremen67
I've never used the Agilnet Connection Manager before
How do I get the agilent drivers for the hdg and dso1074 installed? I have the rigol ones but you mention using the agilent ones
fremen67:
--- Quote from: smgvbest on February 25, 2015, 11:18:01 pm ---@fremen67
I've never used the Agilnet Connection Manager before
How do I get the agilent drivers for the hdg and dso1074 installed? I have the rigol ones but you mention using the agilent ones
--- End quote ---
You just have to install the Agilent (Keysight) IO Libraries Suite. It is now v17.1 and I had v16.3. I just tested with the new version without any problem. You will find it here:
http://www.keysight.com/en/pd-1985909/io-libraries-suite?&cc=FR&lc=fre
fremen67:
Here is a link to my OneDrive:
https://onedrive.live.com/redir?resid=C666E0DC0AF0C9E2!114&authkey=!AMtRrjm2d33uI8Q&ithint=folder%2c
You will find several "upgrade" scripts which you can run from a USB stick, that is whitout opening the case:
- firmware upgrade from 1.00.2 to 1.00.3 (or 1.00.3 back to 1.00.2)
- backup scripts
- model change from HDG2002B to HDG2102C
Have a look at the readme files.
Enjoy!
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version