Products > Test Equipment

Has anybody enabled Tracking Gen on Agilent N9340B?

<< < (15/16) > >>

NA5B:
Hello milesd969, I had the same or similar problem with my N9340B. The logo appeared and stayed forever and nothing else.
This is what I did to fix the problem:
I downloaded Keysight N9340B PC Software and Keysight Connection Expert software first. Found a "Cross Over" LAN cable. Used the device's default 192.168.0.112 IP number. I tried, no success.
Later I set my PC IP to 192.168.0.110  that's what the instructions wrote. Connection Expert program registered the SA as UNKNOWN device! I said ok, at least there is something. I verified this by turning on and off the SA. I was able to see this unknown device appear and disappear.

Later I tried the Keysight N9340B PC Software program. It had a "LAN connection and firmware update" button. I tried to connect to the SA. Again no response. I restarted the software run as admin. Still the same. I ignored this and I went ahead and chose my latest update file. Clicked the UPDATE button and magically it showed the upload bar, uploading files 1,2, and 3 and it stopped for a long time on 3. I was so happy then I got confused. I started thinking that this was a false upgrade move. BUT then it started counting file 4 and up!!!! :- )  So, some files took longer to load. 280 some files later it wrote: Files uploaded, firmware updated, please restart the SA. This file upload took about 10 minutes forever!
I turned the SA off and then on. The Agilent logo stayed a bit longer, then the screen went blank and then showed the actual graphics. Now It works as it should.

milesd969:
Problem solved, I bought another analyzer N9340b from the motherboard, I unsoldered a flash S29GL512P10TFIR1. I used the Xeltek Superpro 3000U programmer, I managed to get the contents of the flash file, using the binary image I filled the old flash, when I started the analyzer everything worked.
I later unlocked all the options for this analyzer model using an algorithm written by a diving man from this forum

WernerFalken:
Bumping this again. Any chance on getting an updated code generator to work on N9342C/N9344C? Works great on the N9340B!

tv84:

--- Quote from: Colby Burkett on March 30, 2023, 06:09:37 am ---Bumping this again. Any chance on getting an updated code generator to work on N9342C/N9344C? Works great on the N9340B!

--- End quote ---

Colby, it's your lucky day. I revised the previous code and added the N9340C generation code.

Here.

tv84:
This is the list of options for N9340C family:


--- Code: ---P06 - Pre-amplifier, 100kHz to 6GHz
TG6 - Tracking Generator, 5MHz to 6GHz
DMA - ASK/FSK Modulation Analysis
AMA - AM/FM Modulation Analysis
PWM - U2000 series support
IBO - IBOC AM and FM
XDS - xDSL Measurement
SIM - Spectrum monitor
CHP - Channel Power
ACP - Adjacent Channel Power Ratio
OBW - Occupied Bandwidth
SEM - Spectrum Emission Mask
FST - Field Strength
F04 - Freq extension to 4.2 GHz
F06 - Freq extension to 6 GHz
F07 - Freq extension to 7 GHz
F13 - Freq extension to 13.6 GHz
F20 - Freq extension to 20 GHz
LAN - LAN port, TCP/IP
RBW - Resolution bandwidth, 10 Hz/3 MHz
FSA - Fine resolution step attenuator
GPS - Built-in GPS receiver and antenna
TPN - Task planner for test automation
TG7 - Tracking Generator, 5 MHz to 7 GHz
SEC - Security features
DST - Temporary License, for demo unit
DT1 - Temporary License
TG4 - Tracking Generator,5 MHz to 4.2 GHz
PA4 - Pre-amplifier, 100 kHz to 4.2 GHz
PA7 - Pre-amplifier, 100 kHz to 7 GHz
P13 - Pre-amplifier, 13.6 GHz
P20 - Pre-amplifier, 20 GHz
CAT - Cable and antenna test
TMG - Time-gated spectrum analysis
BB1 - Baseband input
F7G - Freq extension to 7 GHz
PWS - Power suite
DIA - Diagnostics
F24 - Freq extension to 24 GHz
OPE - Simplified operator mode
SCN - Channel Scanner
CAU - Cable and antenna test
CA7 - Cable and antenna test, 7GHz
CA6 - Cable and antenna test, 6GHz
F08 - Freq extension to 8.5 GHz
PA8 - Pre-amplifier, 100 kHz to 8.5 GHz
PWP - U2020 x-series support
D24 - Temporary License, 24 months
G01 - General-Purpose Interface Bus
CAL - Calibration
RM7 - Reflection Measurement
MNT - Spectrum monitor
PFR - Precision Frequency Reference
P07 - Pre-amplifier, 100 kHz to 7 GHz
EMC - EMC filter and QPeak Detector
TFE - Tracking Generator frequency extension
--- End code ---

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod