Products > Test Equipment

Help restore SDS1102CML+ after unsuccessful flashing

<< < (11/19) > >>

godfather:
@tautech
 Hello , I hope everyone is doing great.
I am having problems with my SDS1102CML+ DSO, Its Stuck at BOOT logo, I tried doing factory recovey but it isnt working, Below is my Serial Log. I request @tautech and other to provide the solution for the same.


--- Code: ---U-Boot 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34)

I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Using default environment

set_default_env::7864
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw
Hit any key to stop autoboot
(Re)start USB...
USB0:   lowlevel init failed
USB error: all controllers failed lowlevel init
Download Linux from USB to Nandflash...
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
Booting from nand ...

NAND read: device 0 offset 0x3080000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Linux-3.2.0+
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2157768 Bytes = 2.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
init started: BusyBox v1.13.2 (2012-04-08 17:28:57 CDT)
starting pid 519, tty '': '/etc/init.d/rcS'
rS in
/etc/init.d/rcS: line 15: setterm: not found
starting pid 536, tty '/dev/ttyO0': '-/bin/sh'

Processing /etc/profile... Done

/ # ./SDS1000_arm.app: relocation error: /usr/lib/libglog.so.0: symbol _ZNSt15basic_streambufIcSt11char_traitsIcEE6setbufEPci, version GLIBCXX_3.4 not defined in file libstdc++.so.6 with link time reference


--- End code ---

With Pendrive 4GB


--- Code: ---U-Boot SPL 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34)
config ddr_pll_config()++
config ddr_pll_config()--
nand_init+++++
nand_init-----
Lcd_Init()++
SetUpLCD()++
SetUpLCD()--
len=768052, height=480, width=800
Logo from nandflash: base=0x81000000; end=0x810bb81f; end-base=0xbb81f; rwsize=0xbb820; r=0x0
Lcd_Init()--


U-Boot 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34)

I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Using default environment

set_default_env::7864
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw
Hit any key to stop autoboot
(Re)start USB...
USB0:   scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Download Linux from USB to Nandflash...
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
Booting from nand ...

NAND read: device 0 offset 0x3080000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Linux-3.2.0+
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2157768 Bytes = 2.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
init started: BusyBox v1.13.2 (2012-04-08 17:28:57 CDT)
starting pid 519, tty '': '/etc/init.d/rcS'
rS in
/etc/init.d/rcS: line 15: setterm: not found
starting pid 536, tty '/dev/ttyO0': '-/bin/sh'

Processing /etc/profile... Done

/ # ./SDS1000_arm.app: relocation error: /usr/lib/libglog.so.0: symbol _ZNSt15basic_streambufIcSt11char_traitsIcEE6setbufEPci, version GLIBCXX_3.4 not defined in file libstdc++.so.6 with link time reference


--- End code ---

tautech:

--- Quote from: godfather on November 06, 2021, 05:06:30 pm ---@tautech
 Hello , I hope everyone is doing great.
I am having problems with my SDS1102CML+ DSO, Its Stuck at BOOT logo, I tried doing factory recovey but it isnt working, Below is my Serial Log.

--- End quote ---
Don't need logs.
Send me PM.

Roman555:
@tautech ,
do you still help owners of digital oscilloscopes Siglent ? Please, help me too.
I also have Siglent SDS1102cml+ (for my hobby) and it doesn't boot anymore.
The story is similar : it was turned off the day before and it didn't boot the next day.
It just stuck on boot logo. I tried to press MATH rapidly and although the device did reset but there were no changes.
Is there a way to restore my digital oscilloscope not opening the case?
Though the warranty is off a long ago...
Thanks!

Upd.
tautech is helping me. Many thanks him.
The oscilloscope appears to be picky about a recovery method (the USB recovery doesn't work because of too old firmware).

Upd2.
My oscilloscope is recovered successfully. Now it also has a fresh firmware  :)
I thank tautech for his help and resources, and also this forum that connects people living all over the world.

tautech:

--- Quote from: Roman555 on September 22, 2022, 07:11:19 pm ---@tautech ,
do you still help owners of digital oscilloscopes Siglent ? Please, help me too.
I also have Siglent SDS1102cml+ (for my hobby) and it doesn't boot anymore.
The story is similar : it was turned off the day before and it didn't boot the next day.
It just stuck on boot logo. I tried to press MATH rapidly and although the device did reset but there were no changes.
Is there a way to restore my digital oscilloscope not opening the case?
Though the warranty is off a long ago...
Thanks!

--- End quote ---
Welcome to the forum.

PM returned.

Rybak27:
Hello!
I have an oscilloscope:

Yesterday it stopped working.  This always displays the boot logo.  I tried resetting with the Math button, but that didn't help.  I want to try flashing it.  Help identify the original model.  I know for sure that this is a plus model, it has an ethernet port.
Sorry for my English :)

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod