Products > Test Equipment

Help restore SDS1102CML+ after unsuccessful flashing

<< < (12/19) > >>

OMAR EDEL:
Hello good night. I have a problem with an oscilloscope siglent SDS 1052DL+. This is in logo stuck, it can start.
Thank you for your help. Best Regards.


U-Boot SPL 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34)
config ddr_pll_config()++
config ddr_pll_config()--
nand_init+++++
nand_init-----
Lcd_Init()++
SetUpLCD()++
SetUpLCD()--
len=768052, height=480, width=800
Logo from nandflash: base=0x81000000; end=0x810bb81f; end-base=0xbb81f; rwsize=0xbb820; r=0x0
Lcd_Init()--


U-Boot 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34)

I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Using default environment

set_default_env::7864
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw
Hit any key to stop autoboot
(Re)start USB...
USB0:   lowlevel init failed
USB error: all controllers failed lowlevel init
Download Linux from USB to Nandflash...
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
Booting from nand ...

NAND read: device 0 offset 0x3080000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Linux-3.2.0+
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2157768 Bytes = 2.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

init started: BusyBox v1.13.2 (2012-04-08 17:28:57 CDT)

starting pid 519, tty '': '/etc/init.d/rcS'
rS in
/etc/init.d/rcS: line 15: setterm: not found

starting pid 536, tty '/dev/ttyO0': '-/bin/sh'

Processing /etc/profile... Done

/ # check_and_upgrade:starting...
mount_fs: rw,sync,ubi1_0,/usr/bin/siglent/usr
ubi1_0unattached
attach_ubi:datafs
attach_ubi:11
UBI device number 1, total 812 LEBs (103104512 bytes, 98.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
MOUNT_DIR_NAME = /usr/bin/siglent/usr
TEST_RESTURN =
is_fs_mounted 0 ---
is_need_upgrade
is_need_upgrade:not need upgrade
check_and_upgrade:end...
++mount_check_copy_appdata: starting
mount_fs: ro,sync,ubi2_0,/usr/bin/siglent/firmdata0
ubi2_0unattached
attach_ubi:firmdata0
attach_ubi:9
UBI device number 2, total 400 LEBs (50790400 bytes, 48.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
MOUNT_DIR_NAME = /usr/bin/siglent/firmdata0
TEST_RESTURN =
is_fs_mounted 0 ---
--mount_check_copy_appdata: ending
Load Fpga Failed!

ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00010000...

tautech:

--- Quote from: OMAR EDEL on January 22, 2023, 04:04:41 am ---Hello good night. I have a problem with an oscilloscope siglent SDS 1052DL+. This is in logo stuck, ........

--- End quote ---
Welcome to the forum.

Close it up and we don't need a dump to fix it.
Send your email address by PM and we will work with you to recover it with our USB tools from Siglent.

Cyrus755:
Hi everybody. My SDS1102CML+ turned into a brick after trying to update the firmware "SDS1000CML+ Firmware_V6.01.01.22 (Release Date 08.06.21)". At the moment, after switching on, only the Siglent logo is displayed on the screen. The oscilloscope startup stops at the Linux kernel starting stage. @tautech can you help resurrect my oscilloscope?

Startup console log

--- Code: ---U-Boot SPL 2013.01.01-svn119138 (Jul 22 2021 - 10:57:19)
config ddr_pll_config()++
config ddr_pll_config()--
nand_init+++++
nand_init-----
Lcd_Init()++
SetUpLCD()++
SetUpLCD()--
len=768052, height=480, width=800
Logo from nandflash: base=0x81000000; end=0x810bb81f; end-base=0xbb81f; rwsize=0xbb820; r=0x0
Lcd_Init()--
 
U-Boot 2013.01.01-svn119138 (Jul 22 2021 - 10:57:19)
 
I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Using default environment
 
set_default_env::7922
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw
Hit any key to stop autoboot
(Re)start USB...
USB0:   lowlevel init failed
USB error: all controllers failed lowlevel init
Download Linux from USB to Nandflash...
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
Booting from nand ...
 
NAND read: device 0 offset 0x3080000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Linux-3.2.0+
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2157768 Bytes = 2.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
 
Starting kernel ...
 
Uncompressing Linux... done, booting the kernel.
--- End code ---

tautech:

--- Quote from: Cyrus755 on January 23, 2023, 07:46:01 pm ---Hi everybody. My SDS1102CML+ turned into a brick after trying to update the firmware "SDS1000CML+ Firmware_V6.01.01.22 (Release Date 08.06.21)". At the moment, after switching on, only the Siglent logo is displayed on the screen. The oscilloscope startup stops at the Linux kernel starting stage. @tautech can you help resurrect my oscilloscope?

Startup console log..............

--- End quote ---
Welcome to the forum.

Button it up, we don't need logs.
Contact me via PM with your email address.

vagalum147:
Hi,

I have the same problem.  The SDS1102CML+, it has the initial screen stuck. I bought it a few months ago to do my hobbies but now I turn it on and it gets stuck on the home screen. Need help and tools like you said. Thank you

UPDATE: All is ok now! Thank you so much, tautech.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod