Products > Test Equipment

HP Logic Analyzer Inverse Assemblers

<< < (26/37) > >>

cmax100000:
I looked at the info in that link and it is close to what I am looking for as I can see the "RC" in a couple of the files from the screen shots.  If I had to pick an IA I would like, 6809 or any of the 6800 series as I am familiar with Motorola assembly in that series.  In the absence of that, any IA will do for what I am trying to find out as it is the configuration learn string that I am messing around with.  It seems like the 1630 could be set up by hand if you had enough patience and experience.
Any help on this is greatly appreciated.

AndersG:
OK. Did you notice the tool i built, for uploading and downloading screenshots? See a bit down on page: http://www.dalton.ax/gpib/

cmax100000:
I didn't see that in the first one but I have now downloaded it and looked at it.  I have a very old setup using a 486 computer running DOS and VBDOS and the utility looks windows based.  All of my gpib access is done through VBDOS.  I have been able to read the learn strings to the computer and break them down somewhat into pods, polarities, clocks, state and timing channels, etc.  As I was doing this and reading the IA posts about the difficulty in getting original files read from a hp gpib drive loaded into a 1630 machine, I thought that maybe the machine was just being set up a certain way which would be readable, savable, and writable as a learn string configuration file.  I was hoping someone on the forum would have a learn string configuration file output from any loaded inverse assembler on a 1630X machine so that I could look and see exactly what settings were being modified so that the assembly language(or machine language) states were captured.  In a perfect world it would be on a 1630D or lower machine as I have byte by byte comparison code that shows the differences between two learn strings.
Hopefully, someone might have something close.
Thanks in advance

ahakman:
Is the Agilent Logic Analysis Software 4.00.1006 cd / dvd image available anywhere? Keysight only has ver 3.67.1008 and 5.90.1110 ISOs available on their site.

5.90 is a PIA in many ways, and lots of people report it is much slower than ver 4 was.

My actual LA has 4.00.1006 on it, and I'd like to be able to install the same version on another box to look at the files offline without the LA (and it's annoying fans) running.

I have 3.67.1008 installed on a virtual machine that I was able to use to compile some IA's for my actual machine on, but if I open the save files from 4.00.1006 in 3.67.1008 on the virtual machine, it just crashes when it's opening the file.

Also if I export a CSV in 4.00 and try to import it into 3.67 (which you'd think would get around the problem of the binary file format), 3.67 complains about there being no license for import, and only imports the first few rows. WTF kind of stupidity is a "license for data import"?

MarkMLl:

--- Quote from: cmax100000 on April 05, 2023, 11:46:25 pm ---I didn't see that in the first one but I have now downloaded it and looked at it.  I have a very old setup using a 486 computer running DOS and VBDOS and the utility looks windows based.  All of my gpib access is done through VBDOS.  I have been able to read the learn strings to the computer and break them down somewhat into pods, polarities, clocks, state and timing channels, etc.  As I was doing this and reading the IA posts about the difficulty in getting original files read from a hp gpib drive loaded into a 1630 machine, I thought that maybe the machine was just being set up a certain way which would be readable, savable, and writable as a learn string configuration file.  I was hoping someone on the forum would have a learn string configuration file output from any loaded inverse assembler on a 1630X machine so that I could look and see exactly what settings were being modified so that the assembly language(or machine language) states were captured.  In a perfect world it would be on a 1630D or lower machine as I have byte by byte comparison code that shows the differences between two learn strings.
Hopefully, someone might have something close.
Thanks in advance

--- End quote ---

I've got code- so far unpublished- which uses a cheap GPIB interface to capture the state of an HP1630G to a .vcd file.

MarkMLl

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod