Products > Test Equipment
HP Logic Analyzer Inverse Assemblers
gslick:
--- Quote from: Hamster on March 11, 2024, 07:33:14 pm ---WooHoo!
Ok, that was a pita to make the 64 bit install files!
gslick, thanks for the tips.. Now to test.
it will be nice to use my bench top 1690D and can retire these old 167X units.
--- End quote ---
Were you able to get the IA DLL build without making any changes to the AnalysisAddIn_vcproj file? When I have tried this a few times with the original AnalysisAddIn_vcproj file (the generated one that you rename to replace the other generated AnalysisAddIn_vcproj file) I have gotten build errors related to agAnalysisAddIn3_i.idl
I have had to add agAnalysisAddIn3_i.idl; to the end of the AdditionalDependencies="agAnalysisAddIn_i.idl;agAnalysisAddIn2_i.idl;" lines to resolve that.
I think someone else here said that the didn't have to do that and didn't get the agAnalysisAddIn3_i.idl errors. I'm not sure what might be going on there.
What host system are you using for the 1690AD? I forget if you can use anything beyond Windows 7 to get the correct 1394 host controller driver loaded. I also forget if it works with both 32-bit and 64-bit versions of Windows 7. A 1690AD with a small and fast somewhat modern PC can be a much better solution than an equivalent slow Windows XP based 1680AD with a small LCD, unless you really need a completely portable all in one analyzer.
Hamster:
Yes, I had to add agAnalysisAddIn3_i.idl; to the proj file.
On the 1690D:
Windows 10 Pro, 64bit , You need to install the compatibility mode drivers on the 1394 card.
I am pretty sure i am running a PCIe card as well, but need to look in the computer to check.
https://www.startech.com/en-us/faq/firewire-cards-windows-legacy-driver-swap
Hamster:
i also converted all my 1680D frames to win7 machines core2duo.. super fast and portable :D
gslick:
--- Quote from: Hamster on March 11, 2024, 08:44:45 pm ---Yes, I had to add agAnalysisAddIn3_i.idl; to the proj file.
On the 1690D:
Windows 10 Pro, 64bit , You need to install the compatibility mode drivers on the 1394 card.
--- End quote ---
Thanks for confirming that you were also seeing the agAnalysisAddIn3_i.idl issue that required a modification of the project file. I wasn't sure if I might have messed up and skipped something in the installation the would have normally prevented that.
Also thanks for confirming that you were able to get your 1690AD working with a Windows 10 host. I'll have to try that myself the next time I get out my 1690AD. I have Dell SFF PC that would make a good Windows 10 host for that.
----------
If anyone is looking for HP preprocessors that attach to 10269 interfaces, this seller on eBay currently has a few listed, although a close look at all of the listing photos is necessary as some of the DIP / PGA target probes are in bad condition. Normally there are a couple of layers of machine pin DIP / PGA sockets on the target probes, so if only the outermost layer has broken pins, the socket layers below the outermost one might be fine and the outmost socket could be removed and replaced.
HP HEWLETT PACKARD 64675 Interface Modules A and B for 68020 Microprocessors
https://www.ebay.com/itm/256411931727
HP HEWLETT PACKARD 10314D Interface Module for 80386 Microprocessors
https://www.ebay.com/itm/256411931693
HP HEWLETT PACKARD 64680A Interface Module for Z8001 Microprocessors
https://www.ebay.com/itm/256410735436
HP HEWLETT PACKARD 64657B Interface Module for 80286 Microprocessors
https://www.ebay.com/itm/266671416022
HP HEWLETT PACKARD E2409A Interface Module for 80286 Microprocessors
https://www.ebay.com/itm/266671415923
HP HEWLETT PACKARD 64670A Interface Module for 68000 Microprocessors
https://www.ebay.com/itm/266671415821
HP HEWLETT PACKARD 64681A Interface Module for Z8002 Microprocessors
https://www.ebay.com/itm/266663873168
HP HEWLETT PACKARD 64658A Interface Module for 80186/80188 Microprocessors
https://www.ebay.com/itm/256405092893
HP HEWLETT PACKARD 64673A Interface Module for 68008 Microprocessors
https://www.ebay.com/itm/266659715690
HP HEWLETT PACKARD 10314B Interface Module for 80386 Microprocessors
https://www.ebay.com/itm/256403930507
HP HEWLETT PACKARD 64655A Interface Module for 8085 Microprocessors
https://www.ebay.com/itm/266659714425
HP HEWLETT PACKARD 10343B SCSI Bus Preprocessor
https://www.ebay.com/itm/256406266462
Hamster:
So, now need to make a nice cheat sheet for pod assignments on the 10269C
cXXXXX_p.txt will indicate the ADDR/DATA assignments, but not which pod goes where.
ie, what are POD1/2/3/4/5 correlate too for ADDR/DATA/STAT
ie, the 80186 uses
Label 0: ADDR (20 bits): A3: ........ ....**** A2: ******** ********
Label 1: DATA (16 bits): A1: ******** ********
Label 2: STAT (10 bits): A5: .....*** ........ A3: *****.** ........
Label 3: SIZE ( 3 bits): A3: *..*.... ........ A2: ........ .......*
Label 4: S6 ( 1 bits): A3: ..*..... ........
Label 5: COPROC ( 9 bits): A5: .....*** ........ A3: ***.*.** ........
Label 6: DMA CH ( 6 bits): A5: .....*** ........ A3: ***..... ........
Which is 65 bits, but doesn't indicate Which bits are were on POD1/2/3/4/5
the good thing is if your ADDR is 16 bits, but the IA needs 24 Bits, it will tell you !
Are we to assume A1 -> POD1 , A2 -> POD2, A3 -> POD3 ?
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version