Products > Test Equipment

Need help hacking DP832 for multicolour option.

<< < (46/91) > >>

Wintel:

--- Quote from: Trident900fi on May 26, 2019, 09:41:00 am ---To update your Rigol DL3021 to DL3021A, here is the complete procedure, without the need of buying the LAN option...
You need:
-Computer with RS232 port
-USB stick formatted in FAT32 with the file keyfile.bin from Tossu (many thanks for the hack !)
-Cross cabel RS232 female-female (2->3; 3->2; 5->5)
-Free software Termite from Compuphase (https://www.compuphase.com/software_termite.htm)

Connect everything together. Start the computer first and launch Termite.
Termite Serial port settings:
-Port COM1 (depend on your computer)
-Baud rate 9600
-Data bits 8
-Stop bits 1
-Parity none
-Flow control none
-Forward none
-Transmitted text Append CR-LF

Turn on the DL3021
To check the connection, you can try to type *IDN? in the Termite command line.
He will return the model of your device.
Type in Termite :PROJ:SET MODEL,DL3021A
That all  :D

--- End quote ---

Can hack the DC Load DL3021 to DL3031A?  Like the DG811 to DG992?

Trident900fi:

--- Quote from: Wintel on May 26, 2019, 07:29:44 pm ---
--- Quote from: Trident900fi on May 26, 2019, 09:41:00 am ---To update your Rigol DL3021 to DL3021A, here is the complete procedure, without the need of buying the LAN option...
You need:
-Computer with RS232 port
-USB stick formatted in FAT32 with the file keyfile.bin from Tossu (many thanks for the hack !)
-Cross cabel RS232 female-female (2->3; 3->2; 5->5)
-Free software Termite from Compuphase (https://www.compuphase.com/software_termite.htm)

Connect everything together. Start the computer first and launch Termite.
Termite Serial port settings:
-Port COM1 (depend on your computer)
-Baud rate 9600
-Data bits 8
-Stop bits 1
-Parity none
-Flow control none
-Forward none
-Transmitted text Append CR-LF

Turn on the DL3021
To check the connection, you can try to type *IDN? in the Termite command line.
He will return the model of your device.
Type in Termite :PROJ:SET MODEL,DL3021A
That all  :D

--- End quote ---

Can hack the DC Load DL3021 to DL3031A?  Like the DG811 to DG992?

--- End quote ---
No, it's not possible, it's not the same hardware inside...
Maybe, if you add the missing components  ;)

joad:
Where do I find the script för extracting all scpi commands like on the DP 800 "dp800_all_commands.txt"

Im looking for scpi commands for calibrating the DL3000.

tossu:

--- Quote from: joad on June 01, 2019, 06:13:59 pm ---Where do I find the script för extracting all scpi commands like on the DP 800 "dp800_all_commands.txt"

Im looking for scpi commands for calibrating the DL3000.

--- End quote ---

There is no fully automated script unless someone else has made one.

Here is a list of commands I have extracted from some version of the DL3000 firmware. There seems to be a bunch of calibration related commands. I hope you will find those usefull.

Gandalf_Sr:
This isn't working for me, I tried 2 different USB drives, formatted FAT32 with just the xxx.bin file on them and my gear says it sees a USB drive.

I am directly connected by LAN and can see my DP832 and DG1022Z in RigolBildschirmkopie after search, I can select them then connect to with the SCPI Commant terminal, issue the *IDN? command to them and see the expected response when I hit [Send & Receive] but when I try to send :PROJ:SET MODEL,DP832A/DG1062Z, in both cases I get a response of...

"There was an error when sending the SCPI command" and after that, the device I just tried to send the :PROJ:SET MODEL,XXXX command to is not seen in RigolBildschirmkopie after search until I cycle power.

I tried using telnet via an admin-level windows powershell (Win 10) but that hangs after I type "telnet 10.0.0.xxx 5555".

Any ideas?

Navigation

[0] Message Index

[#] Next page

[*] Previous page

There was an error while thanking
Thanking...
Go to full version
Powered by SMFPacks Advanced Attachments Uploader Mod