| Products > Test Equipment |
| Need help hacking DP832 for multicolour option. |
| << < (85/91) > >> |
| spiff72:
Hello all, Hoping this isn't the wrong place to ask, as this seems to be discussion around the model change hack, but I just bought and received a secondhand DP832, and immediately updated to the latest firmware. I then tried to apply the riglol hack (entered my serial number on the page, left the AAAA default options, and it generated a licence key. However, when i try to install the key at the "licence" prompt, after entering all the characters, I press OK, and it says "Invalid Serial" number. I have tried twice without success, and even tried regenerating the key on the site several times - it creates the same key every time. Double checked that my serial number was accurate too... Am I doing this wrong? Or is the latest firmware different and no longer allows the licence hack to work? |
| spiff72:
--- Quote from: spiff72 on October 16, 2021, 10:25:38 pm ---Hello all, Hoping this isn't the wrong place to ask, as this seems to be discussion around the model change hack, but I just bought and received a secondhand DP832, and immediately updated to the latest firmware. I then tried to apply the riglol hack (entered my serial number on the page, left the AAAA default options, and it generated a licence key. However, when i try to install the key at the "licence" prompt, after entering all the characters, I press OK, and it says "Invalid Serial" number. I have tried twice without success, and even tried regenerating the key on the site several times - it creates the same key every time. Double checked that my serial number was accurate too... Am I doing this wrong? Or is the latest firmware different and no longer allows the licence hack to work? --- End quote --- UPDATE: I got it to work. Had to do each option separately - skipped the RS232 since I had read that one doesn't work anymore (which is fine by me, and I didn't plan to use it)... Now on the the model upgrade! :-) |
| DTHCoCo:
Hi Mate. Can you please point me in the right direction for the download link of keyfile.bin from Tossu for the Rigol DL3021A Mod regards DTHCoCo |
| _Wim_:
--- Quote from: DTHCoCo on November 13, 2021, 05:00:12 am ---Hi Mate. Can you please point me in the right direction for the download link of keyfile.bin from Tossu for the Rigol DL3021A Mod regards DTHCoCo --- End quote --- https://www.eevblog.com/forum/testgear/need-help-hacking-dp832-for-multicolour-option/msg2320485/#msg2320485 |
| Haru:
For those of you using Windows for Magic USB creation, I wrote a simple step-by-step guide for it. I personally don't own a DP832 yet, but planning on it. Windows Magic Drive creation 1. Open up your diskpart.exe in Administrative mode 2. Select the disk number of your USB drive. 3. Type clean all and wait. - This should take some time, since it is writing zeroes to the blocks. 4. Make partition by typing create partition primary size=1024. - The smaller the size, faster the image dump and writing. - But keep in mind that the sector 0x58E0 should be included. 5. Finally format the partition by format fs=FAT32 QUICK 6. Dump the USB using any kind of tools, output is binary file. 7. Using HxD or other editor, change the data. - If you are not sure which offset should have the *Magic* numbers, the offset should be 0xB1C000 for FAT32. - The sector is 0x58E0, which in decimals 22,752th sector. 8. Save the image file to a certain location. 9. Now write the image to the disk using Rufus or BalenaEtcher, etc. 10. Done! 11. https://www.eevblog.com/forum/testgear/need-help-hacking-dp832-for-multicolour-option/msg2320485/#msg2320485 Side note - I added a 100MB Partitioned Dump binary. This should make things easier by skipping the format and partition creation process. |
| Navigation |
| Message Index |
| Next page |
| Previous page |