Products > Test Equipment
New toy(?) scope Fnirsi DPOX180H, claimed 180MHz/500MSps (May 2023)
solidhit:
ru_tash Menu->System Settings->Transparent menus->Set to 0 to cancel transparency (Tested with v30).
ptluis:
--- Quote from: RAPo on September 27, 2023, 05:55:48 pm ---I've tried it, and I'm going back to the previous version:
-with no signal, the measurement bar is updating several times a second with nonsensical values
-the scope becomes very sluggish both in auto mode and pressing keys.
It takes almost a second to update after a V+ press,
pressing H+ gives a truncated trace for a second, only then refreshes.
quote author=Rooster Cogburn link=topic=377636.msg5081950#msg5081950 date=1695823642]
Fixes:
1: The thickness of the waveform is reduced, making the waveform thinner and clearer.
2: The vertical lines of the square wave are brighter and more obvious
So just some further tweaks to the waveform display. Haven't tried it, but better than nothing, I guess.
--- End quote ---
[/quote]
Isn't "The thickness of the waveform is reduced" against the purpose o DPO scope? some day it will be a DSO ;)
Anyway Fnirsi should give us an option to calibrate the device, it will be of much more interest
ptluis:
--- Quote from: RAPo on September 27, 2023, 05:55:48 pm ---I've tried it, and I'm going back to the previous version:
-with no signal, the measurement bar is updating several times a second with nonsensical values
-the scope becomes very sluggish both in auto mode and pressing keys.
It takes almost a second to update after a V+ press,
pressing H+ gives a truncated trace for a second, only then refreshes.
--- End quote ---
I upgrade it and on my unit only at 50mV/div there's some values updating. at 100mV/div no problems. No sluggish part on my unit after pressing auto and V+ or V- after, everything work fine. No probes connected. Will keep V40. Maybe some hardware thing with your unit? I bought mine in the end of Aug.
This bug not solved:
set FG to 1KHz Square Wave, 2 Vpp, 50% duty
press Auto
Press H+ until H=1us (top indicator) watch the glitch
Keep pressing H+ until H=5ns watch the amazing and wonderfull waveform :palm:
Bellow 32KHz is useless, we can't trust anymore on the displayed image if we zoom in (not zoom button)
ru_tash:
--- Quote from: solidhit on September 28, 2023, 09:08:07 pm ---ru_tash Menu->System Settings->Transparent menus->Set to 0 to cancel transparency (Tested with v30).
--- End quote ---
in my case this does not work, i can set to 0% but when I quit settings menu then no change, it always 100%, v30.
restore to factory settings does not help.
ru_tash:
--- Quote from: ptluis on September 29, 2023, 12:40:03 am ---
--- Quote from: RAPo on September 27, 2023, 05:55:48 pm ---I've tried it, and I'm going back to the previous version:
-with no signal, the measurement bar is updating several times a second with nonsensical values
-the scope becomes very sluggish both in auto mode and pressing keys.
It takes almost a second to update after a V+ press,
pressing H+ gives a truncated trace for a second, only then refreshes.
--- End quote ---
I upgrade it and on my unit only at 50mV/div there's some values updating. at 100mV/div no problems. No sluggish part on my unit after pressing auto and V+ or V- after, everything work fine. No probes connected. Will keep V40. Maybe some hardware thing with your unit? I bought mine in the end of Aug.
This bug not solved:
set FG to 1KHz Square Wave, 2 Vpp, 50% duty
press Auto
Press H+ until H=1us (top indicator) watch the glitch
Keep pressing H+ until H=5ns watch the amazing and wonderfull waveform :palm:
Bellow 32KHz is useless, we can't trust anymore on the displayed image if we zoom in (not zoom button)
--- End quote ---
could be because of low value input ac/dc capacitor?
i've upgraded to v40, no sluggish noticed, they corrected menu with number of open measurements.
transparency still cannot be adjusted.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version